Land Pride RTR1042 Operator'S Manual Download Page 3

1

7/25/13

RTR10 & RTR15 Series Rotary Tillers   311-431M

Land Pride

Important Safety Information

Table of Contents

Important Safety Information

These are common practices that may or may not be applicable to the products described in
this manual.

Look For The Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention
are dependent upon the awareness, concern,
prudence, and proper training of personnel involved
in the operation, transport, maintenance, and storage
of equipment.

!

Be Aware of
Signal Words

A Signal word designates a degree or
level of hazard seriousness. The
signal words are:

Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.

!

DANGER

Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.

Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.

!

WARNING

!

CAUTION

For Your Protection

Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.

Shutdown and Storage

Lower machine to ground, put
tractor in park, turn off engine, and
remove the key.

Detach and store implements in a
area where children normally do
not play. Secure implement by
using blocks and supports.

OFF

REMO

VE

Parts Manual QR Locator

The QR (Quick Reference) code on the front
cover and to the left will take you to the
Parts Manual for this equipment. Download
the appropriate App on your smart phone,
open the App, point your phone on the QR
code and take a picture.

Dealer QR Locator

The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual
QR Locator on this page for
detailed instructions.

Safety at All Times

Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read all
instructions noted on them.

Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.

Operator should be familiar with all
functions of the unit.

Operate implement from the
driver’s seat only.

Make sure all guards and shields
are in place and secured before
operating implement.

Do not leave tractor or implement
unattended with engine running.

Dismounting from a moving tractor
could cause serious injury or
death.

Do not allow anyone to stand
between tractor and implement
while backing up to implement.

Keep hands, feet, and clothing
away from power-driven parts.

Wear snug fitting clothing to avoid
entanglement with moving parts.

Watch out for wires, trees, etc.,
when raising implement. Make
sure all persons are clear of
working area.

Turning tractor too tight may cause
implement to ride up on wheels.
This could result in injury or
equipment damage.

Do not carry passengers on
implement at any time.

Summary of Contents for RTR1042







































Reviews: