Land Pride Rotary Cutters RCR1860 Operator'S Manual Download | Manualshive

Page: 26 / 34

background image

24

Section 5: Maintenance and Lubrication

RCR1860 and RCR1872 Series Rotary Cutters 312-849M

2/03/12

Table of Contents

Lubrication

Gauge Wheel Spindle Tube

Type of Lubrication: Grease

Quantity = 6 pumps

Gauge Wheel Hub

The gauge wheel hub is equipped with a relief hole
located directly opposite the grease fitting. The relief
hole releases pressure from inside the hub casting
when it is greased. The hub should be greased until
grease purges from the relief hole.

Type of Lubrication: Multi-purpose Grease

Quantity = Until grease purges from the relief hole

21416

21416

50

Hrs

Multi-purpose
spray lube

Multi-purpose
grease lube

Multi-purpose
oil lube

Intervals in hours at which
lubrication is required

Lubrication
Legend

24

Hours

8

Hours

Long Term Storage Continued

1.

Clean off any dirt and grease that may have
accumulated on the cutter and moving parts. Scrape
off compacted dirt from the bottom of deck and then
wash surface thoroughly with a garden hose. A
coating of oil may also be applied to the lower deck
area to minimize oxidation.

2.

Check blades and blade bolts for wear and replace if
necessary. See “Cutter Blade Maintenance” on
page 21.

3.

Inspect cutter for loose, damaged or worn parts and
adjust or replace as needed.

4.

Repaint parts where paint is worn or scratched to
prevent rust. Ask your dealer for Aerosol Land Pride
touch-up paint. They are also available in touch-up
bottles with brush, quarts and gallon sizes by adding
TU, QT or GL to the end of the Aerosol part number.

5.

Replace all damaged or missing decals.

6.

Lubricate as noted under “Lubrication” starting on
page 24.

7.

Store cutter on a level surface in a clean, dry place.
Inside storage will reduce maintenance and make for
a longer cutter life.

8.

Follow all unhooking instructions on page 19 when
disconnecting tractor from cutter.

Land Pride Aerosol Touch-up Paint

Part No.

Part Description

821-011C

PAINT LP BEIGE AEROSOL SPRAY CAN

821-002C

PAINT LP BLACK AEROSOL SPRAY CAN

821-054C

PAINT MEDIUM RED AEROSOL SPRAY CAN

821-058C

PAINT GREEN AEROSOL SPRAY CAN

821-066C

PAINT ORANGE AEROSOL SPRAY CAN

821-067C

PAINT BLUE AEROSOL SPRAY CAN

«
...
24
25
26
27
28
...
»

Summary of Contents for Rotary Cutters RCR1860



































Reviews:

No comments

Related manuals for Rotary Cutters RCR1860

Brand: Baroness Pages: 5

Brand: Nakayama Pages: 12

Brand: Dixon Pages: 48

Brand: Garland Pages: 144

Brand: Toro Pages: 48

Brand: Brill Pages: 53

Brand: Toro Pages: 2

Brand: Cub Cadet Pages: 44

Brand: HUSTLER Pages: 65

Brand: Gardena Pages: 290

Brand: Toro Pages: 4

Brand: Lastec Pages: 88

Brand: P.I.T. Pages: 23

Brand: STEELE PRODUCTS Pages: 23

Brand: Cub Cadet Pages: 16

Brand: Cub Cadet Pages: 36

Brand: Snapper Pages: 176

Brand: EINHELL Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands