Land Pride Rear Blades RBT45108, Operator'S Manual

Page: 15 / 38

Section 1: Assembly & Set-Up
RBT4596 & RBT45108 Rear Blades 301-205M 1/13/21
11
Table of Contents
3-Point & Quick Hitch Hook-Up
Figure 1-2
35108
Linchpin
Hitch Pin
QH20 Quick Hitch
Mounting Holes
Upper Holes: Cat. II With Bushings or Cat.III Without Bushings
See step 8 on this page for additional information.
Coupling Storage
Slots (Both Sides)
37298
Cat. III Lower Hitch Pin
Cat. II Lower Hitch Pin Install 1
7/16" O.D. bushings when using
Land Pride’s QH20 Quick Hitch.
Parking Stand
3-Point Hook-Up
WARNING
!
To avoid serious injury or death:
Always shut tractor down according to “Tractor Shutdown
Procedure” provided in this manual before allowing anyone
including the operator to hook up or unhook the implement.
DANGER
!
To avoid serious injury or death:
•
A crushing hazard exists while hooking-up and unhooking
the implement. Keep people and animals away while
backing-up to the implement or pulling away from the
implement. Do not operate hydraulic controls while a
person or animal is directly behind the power machine or
near the implement.
•
Always check all blade hardware for tightness before
moving or working around the unit. Make sure moldboard
pivot and tilt retaining hardware is tightened to the correct
torque. The moldboard can fall from the its pivot mount or
tilt mount if retaining hardware is loose or missing.
Standard 3-Point Hook-Up
Refer to Figure 1-2:
A 3-Point Category II or III hitch is required. The lower
3-Point arms of the 3-Point hitch must be stabilized to
prevent side-to-side movement. Most tractors have sway
blocks or adjustable chains for this purpose.
1. Shorten or remove tractor drawbar to keep it from
interfering with the Rear Blade.
2. Remove linchpins and hitch pins from clevis
lugs.Keep for reuse.
3. Slowly back tractor up to Rear Blade while using
tractor’s 3-Point hydraulic control to align hitch holes
in lower arms with implement’s hitch pin holes.
4. Engage tractor park brake, shut tractor engine off
and remove key before dismounting from tractor or
allowing someone else to hook-up the Rear Blade.
5. With tractor’s lower hitch arms aligned and
positioned in the clevises, insert hitch pins through
the clevis lugs and lower arm hitch holes. Secure
hitch pins with linchpins.
6. Ensure lower arms are stabilized to prevent
excessive side movement.
7. Refer to Figure 1-1 on page 10: Remove hitch
pin (#10) from parking stand (#11) and rotate stand
up. Reinsert hitch pin and secure with hairpin cotter.
8. Connect Cat. II top center link to upper holes using
customer supplied 1" clevis pin & linchpin. If top
center link is Cat. III, drive 1" x 1 1/4" x 1 5/8"
bushings out and connect center link to upper holes
using customer supplied 1 1/4" clevis pin & linchpin.
9. Manually adjust one of the two lower lift arms up or
down to level the Rear Blade from left to right.
10. Manually adjust length of top-link to level Rear Blade
front to rear.
11. Check clearances after all offset, pivot, and tilt
linkages have been installed. Refer to
“Inspection
After Hook-Up” on page 22.
Quick Hitch Hook-Up
Refer to Figure 1-2:
The customer must purchase and install two
1.141" ID x 1.4375" OD x 2 1/2" long busings (Land Pride
Part No. 890-940C) on the lower hitch pins. Also, the
center hitch pin must be moved to the lower hitch holes.
Follow hook-up and unhooking instructions in the Quick
Hitch Operator’s manual when using a Quick Hitch.
NOTE: Land Pride’s Quick Hitch can be attached to
the tractor to provide quick and easy 3-point hook-
up and detachment. See your nearest Land Pride
dealer to purchase a Quick-Hitch.