Land Pride RCF3010 Operator'S Manual Download Page 62 | Manualshive

Page: 62 / 76

background image

Section 5: Maintenance & Lubrication

Table of Contents

RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M

58

11/8/18

RCF3096 Flex Couplers

Figure 5-7

RCF3096 Dual End Flex Couplers

Refer to Figure 5-7 on page 58:

Replace two rubber discs (#1), (Land Pride Part No.
19-075), as follows: If additional repair parts are required,
refer to Land Pride’s Parts Manual 326-566P.

1.

Attach rubber discs (#4) to the double flex yoke (#3)
with 6 bolts (#6A), 12 beaded washers (#1),
6 bushing (#2), and 6 nylock nuts (#7) as shown.
Make sure beads on the beaded washers are facing
the rubber discs. Do not tighten nuts.

2. Attach yoke ends (#5) to rubber discs (#4) with

6 bolts (#6B), 12 beaded washers (#1),
6 bushing (#2), and 6 nylock nuts (#7) as shown.
Make sure beads on the beaded washers are facing
the rubber discs. Do not tighten nuts.

3. Tighten nuts (#7) evenly with nuts torqued 35 to

40 ft-lb. Beaded washers (#2) should be embedded
halfway into the rubber disc.

35085

IMPORTANT:

Make sure beads on beaded washers

(#1) are always facing rubber discs in assembly.

RCF(M)3010 Dual End Flex Couplers

Figure 5-8

RCF(M)3010 Dual End Flex Couplers

Refer to Figure 5-8:

Replace four rubber discs (#4), (Land Pride Part No.
19-075), as follows. If additional repair parts are required,
refer to Land Pride’s Parts Manual 327-088P.

1.

Attach rubber discs (#4A) to the double flex yoke (#3)
with 3 bolts (#6A), 12 beaded washers (#1),
6 bushings (#2), and 3 nylock nuts (#7) as shown.
Make sure beads on the beaded washers are facing
the rubber discs. Do not tighten nuts.

2. Attach yoke end (#5) to rubber discs (#4) with

3 bolts (#6B), 12 beaded washers (#1),
6 bushing (#2), and 3 nylock nuts (#7) as shown.
Make sure beads on the beaded washers are facing
the rubber discs. Do not tighten nuts.

3. Tighten nuts (#7) evenly with nuts torqued 35 to

40 ft-lb. Beaded washers (#2) should be imbedded
halfway into the rubber disc.

4. Repeat steps 1-3 to install rubber discs (#4B) on

opposite end of flex coupler.

35085

Opposite End

IMPORTANT:

Make sure beads on beaded washers

(#1) are always facing rubber discs in assembly.

«
...
60
61
62
63
64
...
»

Summary of Contents for RCF3010













































































Reviews:

No comments

Related manuals for RCF3010

IDEAL Cutters 1035

Brand: Officezone Pages: 3

Brand: CAB Pages: 16

Brand: Omcan Pages: 20

Brand: Milwaukee Pages: 37

Brand: Gardol Pages: 124

Brand: Clarke Pages: 11

Brand: VAIL PRODUCTS Pages: 44

Brand: Palax Pages: 37

Brand: QEP Pages: 8

Vitrex Versatile Power Max 560

Brand: QEP Pages: 5

Brand: Dolmar Pages: 92

Brand: Current Tools Pages: 6

Brand: Haussmann Pages: 42

Brand: EINHELL Pages: 48

Brand: EINHELL Pages: 96

Brand: EINHELL Pages: 152

Brand: EINHELL Pages: 118

Brand: EINHELL Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands