manualshive.com logo in svg

Land Pride RCF2060, Operator'S Manual

Share
Download
Land Pride RCF2060 Operator'S Manual Download Page 10

8

Section 1: Assembly & Set-up

RCF2060 and RCF2072 Rotary Cutters   326-459M

10/18/16

Table of Contents

Section 1: 

Assembly & Set-up

Gearbox Vented Dipstick

Refer to Figure 1-1:

A vented dipstick is shipped loose and packaged with the 
Operator’s Manual. Remove temporary solid plug from 
top of gearbox and replace with vented dipstick. See your 
nearest Land Pride dealer if dipstick is missing. 

Gearbox Vented Dipstick Installation

Figure 1-1

3-Point Hitch & Tailwheel Assembly

Refer to Figure 1-2 on page 9:

1.

Bushings (#4) are zip tied to top hitch (#19).

2.

Snap ring (#6) is shipped stored on clevis pin (#18). 
Remove hairpin cotter (#16), clevis pin (#18), and 
snap ring (#6).

3.

Reattach clevis pin (#18) to A-frames (#2) with 
hairpin cotter (#16). Keep snap ring (#6) for driveline 
assembly.

4.

Remove flat washers (#14) and lock nuts (#12) from 
bolts (#7A).

5.

Reattach A-frames (#2) with 5/8"-11 x 2" GR5 
bolts (#7A), bushings (#4), flat washers (#14), and 
lock nuts (#12). Tighten lock nuts (#12).

6.

Unbolt short crossbar of tailwheel A-frame (#1) from 
adjusting bracket.

7.

Attach A-frame (#1) and 11/16" diameter holes in rear 
brace bars (#3) to the rear deck lugs as shown using 
5/8"-11 x 2" GR5 bolts (#7B) and hex flange lock nuts 
(#12). Draw lock nuts up snug and then back off 1/4 
turn.

IMPORTANT: 

Rotary Cutters are shipped with a 

solid plug in the gearbox to prevent loss of oil during 
shipping and handling. The solid plug on top of the 
gearbox must be replaced with a vented dipstick. Do 
not operate cutter without vented dipstick installed.

30216

DO NOT 

OVERFILL!

 

Oil Level 
Plug

Remove 

Solid Plug

Install 
Vented Dipstick

Tractor Requirements

Tractor horsepower and hitch category should be within 
the range noted below. Tractors outside the horsepower 
range must not be used.

Tractor Horsepower Rating . . . . . . . . . . . . 20 to 65 HP
Hitch Category   . . . . . . . . . . . . . . . . . . . . . . . . .  Cat I
PTO Speed. . . . . . . . . . . . . . . . . . . . . . . . . .540 RPM
PTO Shaft Type  . . . . . . . . . . . . . . . . .  1 3/8"-6 Spline

!

WARNING

Front tractor weights and/or ballast to tires may be required 
to offset weight of implement. Consult your tractor manual to 
determine if additional ballast is required.

Torque Requirements

Refer to 

“Torque Values Chart”

 on page 32 to 

determine correct torque values for common bolts. See 

“Additional Torque Values”

 at bottom of chart for 

exceptions to standard torque values.

Uncrating Instructions

!

WARNING

Always secure cutter with an overhead crane, fork lift, or 
other suitable lifting device before removing hardware bags, 
shipping components, bands, lag screws, and hitch pins. The 
cutter can suddenly fall causing serious injury or death.

1.

Secure cutter with a hoist or other lifting device 
before removing shipping hardware.

2.

Cut shipping straps securing driveline and hitch 
straps (#5) to the shipping crate. Remove driveline 
from shipping crate and lay gently hitch straps down 
onto the shipping crate.

3.

5-pack only:

 Remove bar at the top connecting this 

cutter to other cutters. Be sure to replace the bolts in 
the cutter and to tighten it to the correct torque. 

4.

Remove lag screws securing front face of cutter to 
the crate.

5.

Using lifting device, remove tension on hitch pins 
securing clevis plates to shipping crate.

6.

Remove hitch pins from clevis plates and lift cutter 
from shipping crate.

7.

Gently lower cutter onto the working area. Be careful 
not to allow hitch straps (#5) to fall onto the plastic 
manual tube.

NOTE:  

When lowering cutter onto the working area, 

keep hitch straps (#5) from falling onto the manual 
tube and breaking the tube.

Summary of Contents for RCF2060





































Reviews:

No comments

Brands by name

Popular brands

Load more brands