Section 1: Assembly & Set-up
RCB5715 & RCBM5715 Rotary Cutter 337-046M
7/8/20
15
Serial Number Plate Location
Figure 1-1
Tractor Requirements
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used.
Horsepower Rating . . . . . 60-250 hp (44.7-186.4 kW)
Hitch Type . . . . . . . . . . . . . . . . . . . . . . . . . . Drawbar
(See
Rear Power Take-off Speed:
RCB5715 . . . . . . . . . . . . . . . . . . . . . . . . . 540 rpm
RCMB5715 . . . . . . . . . . . . . . . . . . . . . . . .1000 rpm
Hydraulic Outlets
Simultaneous Wing Fold . . . . . . . . .2 duplex outlets
Independent Wing Fold . . . . . . . . . 3-duplex outlets
(See
Enclosed Cab or Operator Shield. . . . Recommended
DANGER
!
To prevent serious injury or death:
Rotary Cutters have the ability to discharge objects at high
speeds; therefore, the use of front & rear safety guards is
mandatory with this cutter. Double row chain guards should be
used when cutting along roadways and in areas where people
may be present. Stop blade rotation if bystanders are in or
around the area. It is recommended that a safety shield be
placed between the operator and cutter on an open air tractor.
WARNING
!
To prevent serious injury or death:
Do not use a tractor that is too small or too large. Small
tractors can be pushed around and flipped over. Large tractors
can damage the attached implement.
73866
Power Take-off Drawbar Distance
Figure 1-2
Drawbar Set-up
Refer to Figure 1-2:
WARNING
!
To prevent serious injury or death:
•
Do not use a power take-off adapter. The adapter will
increase strain on the tractor’s power take-off shaft causing
possible damage to shaft and driveline. It will also defeat
the purpose of the tractor’s power take-off shield.
•
Power take-off damage may occur if distances “A” and
“B” are not properly maintained.
Maintain proper distance “A” between center of drawbar
hitch pin hole and end of tractor power take-off shaft.
540 rpm & 1 3/8", 1000 rpm power take-off speed:
“A” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14"- 16"
“B” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8"- 10"
“C” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18"- 22"
1 3/4", 1000 rpm power take-off speed:
“A” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18"- 20"
“B” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10"- 12"
“C” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18"- 22"
Hydraulic Outlets
Depending on purchased fold option, two to three duplex
outlets are required. One of the outlets is required for
raising and lowering the deck height. A second outlet is
required when choosing an option to fold both wings
simultaneously. The third outlet is required when
choosing an option to fold each wing independently.
Land Pride highly recommends connecting the wing fold
hose(s) to a duplex outlet with float capabilities and using
the float capability when in field operation.
22273
A
Power Take-off Shaft
Drawbar
B
Ground Level
C
Section 1: Assembly & Set-up
