Land Pride RB45108 Operator'S Manual Download Page 4

2

Important Safety Information

RB4596, RB45108 & RB5596 Rear Blade   301-133M

5/21/07

Land Pride

Table of Contents

Transport
Machinery Safely

Comply with state and local laws.

Maximum transport speed for

implement is 20 mph. DO NOT
EXCEED. Never travel at a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.

Sudden braking can cause a

towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.

Use the following maximum

speed - tow load weight ratios as
a guideline:

20 mph when weight is less
than or equal to the weight of
tractor.
10 mph when weight is double
the weight of tractor.

IMPORTANT: Do not tow a load

that is more than double the
weight of tractor.

Use Safety
Lights and Devices

Slow moving tractors, self-

propelled equipment, and towed
implements can create a hazard
when driven on public roads. They
are difficult to see, especially at
night.

Flashing warning lights and turn

signals are recommended
whenever driving on public roads.
Use lights and devices provided
with implement.

Practice Safe Mainte-
nance

Understand procedure before

doing work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.

Work in a clean dry area.

Lower the implement to the

ground, put tractor in park, turn off
engine, and remove key before
performing maintenance.

Allow implement to cool

completely.

Do not grease or oil implement

while it is in operation.

Inspect all parts. Make sure parts

are in good condition & installed
properly.

Remove buildup of grease, oil or

debris.

Remove all tools and unused

parts from implement before
operation.

Use A Safety Chain

A safety chain will help control

drawn machinery should it
separate from the tractor
drawbar.

Use a chain with the strength

rating equal to or greater than
the gross weight of the towed
machinery.

Attach the chain to the tractor

drawbar support or other
specified anchor location. Allow
only enough slack in the chain to
permit turning.

Do not use safety chain for

towing.

These are common practices that may or may not be applicable to the products described in
this manual.

Summary of Contents for RB45108























Reviews: