Land Pride LR16 Series, Operator'S Manual, Page: 12 / 30

Section 1: Assembly & Set-up
Table of Contents
LR1660, LR1672, LR1684 & LR1696, LR2684 & LR2696 Landscape Rakes 302-305M 11/27/18
8
Tractor Requirements
WARNING
!
To prevent serious injury or death:
• Lightweight tractors with rear attached implements may
need weights added to the front to maintain steering control.
Consult your tractor Operator’s Manual to determine
proper weight requirements and maximum weight
limitations.
•
Do not use a tractor that is too small or too large. Small
tractors can be pushed around and flipped over. Large
tractors can damage the attached implement.
Tractor horsepower and hitch category should be within
the range noted below. Tractors outside the horsepower
range must not be used.
LR16 Series Horsepower Rating ...................20-40 hp
LR26 Series Horsepower Rating ...................25-60 hp
3-Point Hitch Category ...................................... Cat. 1
Hydraulic Outlets for Hydraulic Angling Kit ...1 Duplex
LR16 Landscape Rake Assembly
Refer to Figure 1-1:
DANGER
!
To prevent serious injury or death:
Components falling from the implement can injure a person.
Make certain all components are secured to the implement
before lifting it, and that the unit is properly supported on the
ground before removing lifting device. Always keep feet and
other extremities clear of areas where components can fall.
1. Position mounting bracket (#3) with ears pointing
forward as shown and attach to underside of
mainframe (#2) with two 3/8"-16 x 1" GR5 hex flange
serrated screws (#11) and hex flange locknuts (#16).
Tighten locknuts to the correct torque.
2. Attach park stand (#4) to mounting bracket (#3) with
3/8"-16 x 3" GR5 bolt (#13) and hex flange locknut
(#16). Draw locknut up snug, do not tighten.
3. Rotate park stand (#4) down and secure with wire
snap locking pin (#23). Make certain wire snap is
fastened over end of pin to retain pin.
4. Remove hex flange cap screw (#25), pivot cap (#5),
drive pivot cap (#6), and pivot bushing (#24), from
rake pivot shaft (#7).
5. Insert pivot shaft (#7) into hole in mainframe (#2).
6. Attach pivot bushing (#24), drive pivot cap (#6), and
pivot cap (#5) to pivot shaft (#7) with 3/4"-10 x 1 1/2"
GR5 hex flange cap screw (#25). Tighten cap screw
to the correct torque.
IMPORTANT: Remove paint from rake pivot shaft
and wipe grease from inside of mainframe pivot hole
to make certain pivot shaft will fit into pivot hole.
Section 1: Assembly & Set-up
LR16 Series Landscape Rake Assembly
Figure 1-1
7. Align hole “A” in rake turntable with hitch pin
hole “B” and insert 3/4" hitch pin (#19). Secure hitch
pin with hairpin cotter (#20).
8. Attach upper hitch (#1) to mainframe (#2) with
1/2"-13 x 3" GR5 hex head flange cap screws (#12)
and hex flange locknuts (#15). Tighten locknuts to the
proper torque.
9. Attach Quick Hitch bushing (#8) to upper hitch (#1)
with 3/4"-10 x 3 1/2" hex cap screw (#10) and hex
flange top locknut (#17). Tighten top locknut to the
correct torque.
10. Adjust jamb nuts (#21) on draw pins (#22) until
distance from face of jam nut to center of linchpin
hole is 1.53" (1 17/32") minimum.
11. Attach draw pins (#22) to main frame (#2) with spring
lock washers (#18) and 7/8"-14 hex nuts (#14). Draw
hex nuts up snug. Do not tighten until next step.
12. Keep draw pins (#22) from turning by inserting an
alignment punch into the linchpin hole. Keep linchpin
hole vertical with alignment punch while tightening
hex nuts (#14) to the correct torque.
DANGER
!
To prevent serious injury or death:
Always check all rake hardware for tightness before moving or
working around the unit. Make sure pivot retaining hardware
is tighten to the correct torque. The rake can fall from its pivot
mount if retaining hardware is loose or missing.
33837