![background image](http://html.mh-extra.com/html/land-pride/grading-scrapers-gs2584/grading-scrapers-gs2584_operators-manual_673004011.webp)
Section 1: Assembly & Set-up
9/25/18
GS2572, GS2584 & GS2596 Grading Scrapers 303-268M
7
Section 1: Assembly & Set-up
Shank Assembly (Optional)
Refer to Figure 1-1 on page 6:
When possible, the shanks are shipped assembled to the
Grading Scraper. Some shanks may need installation.
DANGER
!
To prevent serious injury or death:
Make adjustments to the implement after it has been properly
attached to a tractor and secured with solid non-concrete
supports in the up position. Never work around or under
equipment supported by hydraulics. Hydraulics can drop
equipment instantly if controls are actuated or if hydraulic
lines burst even when power to hydraulics is shut off.
WARNING
!
To prevent serious injury or death:
•
Always keep your body extremities out from under the
shanks while adjusting them. It is possible for the shanks to
fall causing injury to your feet and/or legs.
•
Keep clear of the shank slots while adjusting shank height.
Shanks can pinch body parts in the slots during adjustments.
Before installing shanks (#15), attach Grading Scraper to
the tractor’s 3-point hitch or raise front of scraper up and
support it with blocks. See
“3-Point Hook-up”
on page 8.
1.
Remove shanks (#15) from shipping crate and insert
them into the front slots with tips pointing forward.
2. Secure shanks with lock pins (#14) and
hairpin cotters (#11).
NOTE:
See Section 2: Adjustments for shank depth.
Tractor Requirements
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used.
Required Horsepower Rating . . . 40 to 90 horsepower
Hitch Type . . . . . . . . . . . . . 3 - Point Cat. I and Cat. II
WARNING
!
To avoid serious injury or death:
Lightweight tractors with rear attached implements may need
weights added to the front to maintain steering control.
Consult your tractor Operator’s Manual to determine proper
weight requirements and maximum weight limitations.
Torque Requirements
Refer to
“Torque Values Chart”
on page 18 to
determine correct torque values of fasteners during
assembly.
Hitch Assembly
Refer to Figure 1-1 on page 6:
1.
Remove linchpins (#10) from hitch pins (#4).
2. Position hitch straps (#1 & #2) with large holes (A)
towards the front and mount large holes over end of
hitch pins (#4).
3. Attach middle and rear holes in hitch straps to clevis
plates with 3/4"-10 x 2" GR5 cap screws (#6), lock
washers (#9), and hex nuts (#8) as shown. Do not
tighten hardware at this time.
4. Reinsert linchpins (#10) and snap wire retainer over
hitch pins to secure hitch pins.
5. Attach channel brace (#3) to rear mounting lugs with
3/4"-10 x 5" GR5 cap screw (#7B), lock washer (#9),
and hex nut (#8). Do not tighten bolt at this time.
6. Attach channel brace (#3) and spacer (#5) to hitch
straps (#1 & #2) as shown with 3/4"-10 x 5" GR5 cap
screw (#7A), lock washer (#9), and hex nut (#8). Do
not tighten hardware at this time.
7.
Draw all six hex nuts (#8) up snug. Make certain hitch
pins (#4) are loose in their holes. If hitch pin is tight,
readjust hitch frames (#1 & #2) until loose and then
tighten all six hex nuts (#8) to the correct torque.
8. Install 3/4" x 3 3/4" hitch pin (#12) to hitch straps and
secure in place with hairpin cotter (#13).