Land Pride FSP1000 Operator'S Manual Download

Page: 21 / 32

Section 3: Adjustments

FSP500, FSP700 & FSP1000 Broadcast Spreaders 309-065M

11/29/18

Dispersal Pattern

Refer to Figure 3-1, Figure 3-2 & Figure 3-3:

Product dispersal is controlled by properly opening and
closing left and right gates at the hopper bottom with
adjustment levers (#1 & #2).

Some adjustment to the distributor vanes may be
required. See detailed instructions for

“Distributor Vane

Adjustment”

on page 18.

Positioning right and left gate levers as follows:

Left Side Dispersal,

View (A) in Figure 3-1

Refer to Figure 3-3:

Remove lever locking knob (#3).

2. Close right gate by moving adjustment lever (#1)

above gate setting position #1.

3. Move adjustment lever (#2) to the selected gate

setting provided in spreading charts on page 19 for
lbs/acre and page 20 for kgs/hectare.

4. Secure adjustment lever (#2) by placing hair pin

cotter (#5) in the selected gate setting hole with
adjustment lever (#2) resting on top of hairpin (#5).

Full Width Dispersal,

View (B) in Figure 3-1

Refer to Figure 3-2 & Figure 3-3:

Lock adjustment levers (#1 & #2) together with lever
locking knob (#3).

2. Move adjustment levers together just above selected

gate setting provided in spreading charts on
page 19 for lbs/acre and page 20 for kgs/hectare.

3. Secure adjustment levers by placing hair pin

cotter (#5) in the selected gate setting hole with
adjustment levers resting on top of hairpin (#5).

Right Side Dispersal,

View (C) in Figure 3-1

Refer to Figure 3-3:

Remove lever locking knob (#3).

2. Close left gate by moving adjustment lever (#2) up

above gate setting position #1.

3. Move adjustment lever (#1) to the selected gate

setting provided in spreading charts on page 19 for
lbs/acre and page 20 for kgs/hectare.

4. Secure adjustment lever (#1) by placing hair pin

cotter (#5) in the selected gate setting hole with
adjustment lever (#1) resting on top of hairpin (#5).

Delivery Direction

Figure 3-1

Lever Adjustments

Figure 3-2

Gate Setting Hole Numbers

Figure 3-3

13611

13610

24980

Section 3:

Adjustments

Summary of Contents for FSP1000

































Search results

Summary of Contents for FSP1000

Reviews:

Related manuals for FSP1000

Brands by name

Popular brands

Land Pride FSP1000, Operator'S Manual

Search results

Summary of Contents for FSP1000

Reviews:

Related manuals for FSP1000

Brands by name

Popular brands