background image

12

Section 1: Assembly & Set-up 

FSP500, FSP700 & FSP1000 Broadcast Spreaders 309-065M

Table of Contents

11/29/18

Check Driveline Minimum Length

Figure 1-8

Check Subcompact Tractor fit-up

Use instructions below when hooking-up a subcompact 
tractor or Kubota BX tractor. If the tractor is a standard 
size tractor, go to 

“Check Standard Tractor Fit-up” 

on 

page 11. 

Refer to Figure 1-8:

1.

With driveline attached only to the spreadser, remove 
outer driveline (tractor end) from inner driveline to 
separate the two profiles.

2. Park tractor and spreader on a level surface. 

3. Raise spreader until gearbox input shaft is level with 

tractor power take-off shaft. Securely block spreader 
at this height to keep the unit from lowering. 

4. With spreader resting on the support blocks, 

shutdown tractor using 

“Tractor Shutdown 

Procedure” 

on page 9.

5. Attach outer driveline half to the tractor’s power take-

off shaft. Refer to 

“Driveline Hook-up” 

on page 10.

6. Hold inner and outer drivelines parallel to each other 

as shown in Figure 1-6. Measure dimension “A”.

If "A" is less than 2", continue with step 10. 

If “A” is greater than or equal to 2", continue with 
step 7 below. 

7.

Remove outer driveline from the tractor and apply 
multi-purpose grease to the inside of its outer shaft.

8. Reassemble the two driveline halves together.

9. Implement end of the driveline should still be 

attached to the spreader gearbox. Hook-up tractor 
end of the driveline to the power take-off shaft. See 

“Driveline Hook-up” 

on page 10.

24976

IMPORTANT

A driveline that is too long can bottom 

out causing structural damage to the tractor and 
implement. Always check driveline minimum length 
during initial setup, and when connecting to a 
different tractor. More than one driveline may be 
required to fit all applications.

Shorten Driveline Length

Figure 1-9

10. If dimension “A” is less than 2", shorten driveline as 

follows:

Refer to Figure 1-7:

a. Measure 2" (

“B1”

 dimension) back from outer 

driveline shield and make a mark at this location 
on the inner driveline shield.

b. Measure 2" (

“B2”

 dimension) back from the inner 

driveline shield and make a mark at this location 
on the outer driveline shield.

11. Remove outer driveline from the tractor power take-

off shaft and inner driveline from the spreader 
gearbox shaft. 

12. Cut off non-yoke end of inner driveline as follows:

a. Measure from end of inner shield to scribed mark 

(

“X”

 dimension) and record. 

b. Cut off inner shield at the mark. Cut same amount 

off the inner shaft (

“X1”

 dimension). 

13. Cut off non-yoke end of outer driveline as follows:

a. Measure from end of outer shield to scribed mark 

(

“Y”

 dimension) and record. 

b. Cut off outer shield at the mark. Cut same amount 

off the outer shaft (

“Y1”

 dimension). 

14. Remove all burrs and cuttings.

15. Apply multi-purpose grease to the inside of the outer 

shaft and reassemble the driveline.

16. Attach driveline to the spreader and tractor. Refer to 

“Driveline Installation”

 and 

“Driveline Hook-up” 

on page 10.

24976

Summary of Contents for FSP1000

































Reviews: