background image

Table of Contents

11/28/18

© 

Copyright 2018 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future. 

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

BB4596, BB4510, & BB4512 Pull Type Drag Scraper 306-096M

Table of Contents

Important Safety Information   . . . . . . . . . . . . .  1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol  . . . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction   . . . . . . . . . . . . . . . . . . . . . . . . . . .  6

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . . 6

Terminology  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Definitions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Serial Number   . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Further Assistance  . . . . . . . . . . . . . . . . . . . . . . . . 6

Section 1: Assembly & Set-up   . . . . . . . . . . . .  7

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . . 7
Dealer Preparations   . . . . . . . . . . . . . . . . . . . . . . . . 7
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . . 7
Special Uncrating Instructions . . . . . . . . . . . . . . . . . 7

Tongue and Axle Removal  . . . . . . . . . . . . . . . . . . 7
Wheel Installation . . . . . . . . . . . . . . . . . . . . . . . . . 8
Weight Box Removal (Optional)  . . . . . . . . . . . . . . 8
Drag Scraper Removal . . . . . . . . . . . . . . . . . . . . . 9

Tongue Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hitch Options & Assembly . . . . . . . . . . . . . . . . . . . 10

Clevis Hitch   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Swivel Clevis Hitch . . . . . . . . . . . . . . . . . . . . . . . 10
Swivel Ball Hitch   . . . . . . . . . . . . . . . . . . . . . . . . 10

Standard Axle & Park Jack  . . . . . . . . . . . . . . . . . . 11
Tilt Axle & Park Jack  . . . . . . . . . . . . . . . . . . . . . . . 12
Weight Box Assembly (Optional) . . . . . . . . . . . . . . 13
LED Light Kit Option  . . . . . . . . . . . . . . . . . . . . . . . 14

Section 2: Operating Procedures  . . . . . . . . .  16

Startup Checklist  . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . 16
Tractor Hook-up   . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Hook-up LED Lights   . . . . . . . . . . . . . . . . . . . . . . . 17
Transporting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Field Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
General Operating Instructions  . . . . . . . . . . . . . . . 18
Unhook Tractor  . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Section 3: Optional Equipment  . . . . . . . . . . .  20

Standard or Tilt Axle  . . . . . . . . . . . . . . . . . . . . . . . 20
Weight Box  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Section 4: Maintenance & Lubrication   . . . . . 21

General Maintenance Information  . . . . . . . . . . . . . 21
Tractor Maintenance  . . . . . . . . . . . . . . . . . . . . . . . 21
Cutting Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 21
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 22
Lubrication Points   . . . . . . . . . . . . . . . . . . . . . . . . . 22

Axle Hub Bearings  . . . . . . . . . . . . . . . . . . . . . . . 22
Tilt Axle Pivot Point   . . . . . . . . . . . . . . . . . . . . . . 22

Section 5: Specifications & Capacities  . . . . . 23
Section 6: Features & Benefits   . . . . . . . . . . . 25
Section 7: Torque Values Chart  . . . . . . . . . . . 26
Section 8: Warranty   . . . . . . . . . . . . . . . . . . . . 27

Summary of Contents for BB4596

































Reviews: