background image

18

Section 4: Maintenance and Lubrication

FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle   310-148M

10/11/06

Land Pride

Table of Contents

Gearbox

Check the oil level in the gearbox by removing the bottom
plug in the back of the box. Add oil if necessary into the plug
on the top of the gearbox. Retighten both plugs.

Type of Lubrication: SAE 90 Oil

Quantity = Until oil reaches outside plug hole

IMPORTANT: Should your gearbox require repair,
take it to your Land Pride Dealer! Check oil level in
gearbox every 50 hours of operation.

16648

DO NOT
OVERFILL!

Fill

25

Hours

PTO U-Joint

Coat PTO u-joint with grease every 8 hours of operation

Type of Lubrication: Multipurpose

Quantity = Coat Generously

12559

50

Multi-purpose
spray lube

Multi-purpose
grease lube

Intervals in hours
at which lubrication
is required

Lubrication
Legend

Multi-purpose
oil lube

8

Hours

Lubrication

!

CAUTION

For Safety reasons, each lubrication operation must be
performed with the tractor’s PTO disengaged, the mower
lowered completely, tractor engine shut off and ignition key
removed.

Service Daily

1.

Grease the PTO u-joints.

2.

Wheel support bushings.

3.

Wheel bushing.

4.

Bearing in blade spindle hubs.

Service Every 50 Hours Of Operation:

1.

With the mower on level ground, check the oil level in
the gearbox by removing the plug in the side of the
box. The oil should reach the plug hole. If oil level is
low, remove the top plug in the gearcase and fill with
SAE 90 oil until oil flows from side port of the
gearbox. Reinstall plugs and retighten.

2.

Disconnect PTO shaft from the tractor and slide
apart. Clean and coat the inner tube of the PTO shaft
with a light film of grease and then reassemble.

IMPORTANT: Do not overfill! Should your gearbox
require repair, take it to your Land Pride dealer.

PTO Shaft

Disconnect PTO shaft from the tractor and slide apart.
Clean and coat the inner tube of the PTO shaft with a light
film of grease and then reassemble.

Type of Lubrication: Multipurpose

Quantity = Light Film

12559

20

Hours

Oil

Level

Fill

Oil

Level

23582

Summary of Contents for at 2560




























Reviews: