background image

Section 3: Operating Instructions 

Table of Contents

AFM3011 All-Flex Grooming Mower 315-783M

3/21/19

26

Section 3: 

Operating Instructions

Introduction

Hazard control and accident prevention are dependent 
upon the awareness, concern, prudence and proper 
training involved in the operation, transport, maintenance 
and storage of the grooming mower. Therefore, it is 
absolutely essential that no one operates the mower 
unless they are age 16 or older and have read, fully 
understood, and are totally familiar with the Operator’s 
Manual. Make sure the operator has paid particular 
attention to:

Important Safety Information

, page 1

Section 1: Assembly & Set-up,

 page 15

Section 2: Adjustments

, page 22

Section 3: Operating Instructions

, page 26

SSection 5: Maintenance & Lubrication

, page 35

Perform the following inspections before using your 
mower. 

Operating Checklist

Check

Ref.

Read and follow all Safety Rules carefully. 
Refer to “Important Safety Information”.

1

Make sure all safety labels are in place. 
Refer to "Safety Labels".

6

Make sure there are no hydraulic leaks. Refer 
to “Avoid High Pressure Fluids Hazard”.

3

Read and follow hook-up & preparation 
instructions. See "Section 1: Assembly & Set-up".

15

Make sure the hitch safety chain is securely 
attached to the mower hitch and tractor.

18

Make a thorough examination of the main 
driveline installation. Check driveline 
connections between gearboxes and between 
tractor power take-off and mower gearbox.

18 

Read and make all required adjustments. 
Refer to "Section 2: Adjustments".

22

Read and follow all maintenance instructions. 
See "Section 5: Maintenance & Lubrication".

35

Inspect blades for wear and sharpness.

36

Read and follow all lubrication instructions. 
Refer to "Lubrication Points".

40

Check mower initially and periodically for 
loose bolts and pins. Refer to “Torque Values 
Chart” for tightness.

52

Check tire pressure. 
Refer to "Tire Inflation Chart".

52

General Safety

DANGER

!

To avoid serious injury or death:  

All guards and shields must be installed and in good 

working condition while operating the implement.

Tractor power take-off shaft shield, driveline shields, and 

gearbox shaft shields must be installed and in good working 
condition to avoid driveline entanglement and projectiles 
flying off of the driveline.

Do not allow anyone near the tractor or implement while 

operating. Stop operation if bystanders are too close. They 
can be hit by flying projectiles, become entangled in the 
equipment, or ran over.

Keep all persons away from the blades while they are 

rotating. Never place hands or feet under the deck with 
blades rotating or when tractor engine is running. Do not 
operate implement or tractor if bystanders are in the area.

Do not transport without transport locks securely engaged. 

Do not walk or work underneath a raised wing unless all 
transport locks are securely engaged. Wings can drop 
suddenly if a transport lock is not securely engaged.

Do not use a power take-off adapter. The adapter will 

increase strain on the tractor’s power take-off shaft causing 
possible damage to shaft and driveline. It will also defeat 
the purpose of the tractor’s power take-off shield.

WARNING

!

To avoid serious injury or death:  

Allow only persons to operate this implement who have 

fully read and comprehended this manual, who have been 
properly trained in the safe operation of this implement, and 
who are age 16 or older. Serious injury or death can result 
from the inability to read, understand, and follow 
instructions provided in this manual.

Operate only power machines equipped with a certified 

Roll-Over Protective Structure (ROPS) and seat belt. Keep 
folding ROPS in the “locked up” position when 
appropriate. If ROPS is in the locked up position, fasten seat 
belt snugly and securely to help protect against serious 
injury or death from falling and machine overturn.

Never carry riders on the implement or tractor. Riders can 

obstruct the operator’s view, interfere with control of the 
equipment, be pinched by moving components, become 
entangled in rotating components, be struck by objects, be 
thrown or fall from the equipment, etc.

Do not engage power take-off with AFM decks in the raised 

position or with engine speed above idle. Doing so will 
damage power train components.

Always disengage tractor PTO before raising mower decks 

to transport position to avoid power train damage, injury 
from thrown objects, or blade contact.

Always follow “Tractor Shutdown Procedure” provided in 

this manual before dismounting the tractor.

Summary of Contents for AFM3011



























































Reviews: