Land Pride 3P500 Original Instructions Manual Download | Manualshive

Page: 26 / 52

background image

Adjustments

Table of Contents

22

3P500, 3P500V, & 3P600



313-517M

2018-06-12

Disc Blade Adjustments

Raise drill and block it up or lock it up.

Opener Disc Spacing

Sharp Object Hazard:
Be careful working around and handling disc blades. Wear
gloves. Edges of both new and well-worn blades can be sharp.

Opener disc angle and stagger is not adjustable, but
disc-to-disc spacing is, and may need attention as discs
experience normal wear. Spacers must be reset when
blades are replaced.

Refer to Figure 13

The ideal spacing causes the blades to be in contact for
about one inch. If you insert two pieces of paper between
the blades, the gap between them should be

0 to 1.75 in. (0 to 4.4 cm)

If the blades do not touch, they should at least be close
enough so that a business card encounters some friction
when passing between them.

If the contact region is significantly larger or the gap too
wide, it needs to be adjusted by moving one or more
spacer washers. If the contact region varies with blade
rotation, one or both blades is likely bent and in need of
replacement. If removing all spacers cannot bring the
blades into contact, they are worn out and need
replacing.

Adjusting Disc Contact

Refer to Figure 14

1.

Remove the bolt

retaining the opener disc on one

side. Carefully remove the disc, noting how many
spacers

are outside the disc and inside the disc.

Do not lose the hub components and dust cap

.

Note: It is not necessary to remove the hub flange or

bearing for this adjustment.

2.

To reduce the spacing between the discs (the normal
case), move one spacer washer

from the inside to

the outside of the disc. It may be necessary to
loosen the scraper (page 23) to reduce disc-to-disc
spacing.

3.

Re-assemble and check disc contact.

4.

Re-adjust scraper.

Figure 13

Checking Disc Contact

26451

1

2

3

2

Figure 14

Adjusting Disc Spacers

26385

1

2

3

1

«
...
24
25
26
27
28
...
»

Summary of Contents for 3P500





















































Reviews:

No comments

Related manuals for 3P500

Relion 670 series

Brand: ABB Pages: 66

Brand: Rangevision Pages: 31

Brand: KaVo Pages: 16

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: G-Systems Pages: 60

Brand: G-Lab Pages: 16

Brand: G&G Pages: 2

Brand: IDEAL Pages: 12

Brand: jablotron Pages: 2

ENET-232 Series

Brand: National Instruments Pages: 105

Brand: natus Pages: 20

Dantec Keypoint G4

Brand: natus Pages: 42

Brand: natus Pages: 149

Brand: Radial Engineering Pages: 16

Brand: R&S Pages: 61

Brand: ubbink Pages: 30

Brand: Ultimate Healthcare Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands