background image

Section 7: Features & Benefits 

Table of Contents

AFM4211 All-Flex Grooming Mower 315-507M

3/8/23

48

AFM4211 All-Flex Grooming Mowers

Features

Benefits

LED Signal lights

LED lights are bright, long lasting, and resistant to vibration, unlike incandescent 
counterparts.

Counter blade rotation 
on left-hand deck

Spreads grass clippings more evenly. Wing decks throw grass away from the rear 
deck. Rear deck doesn’t get covered up nor does it get bogged down by cut grass.

7'-8" (2.34 m) transport width

Meets most city/county codes for transport width. 

6" (15.2 cm) Deck overlap

Eliminates skipping when going into a tight turn.

11'-1" (3.38 m) Cutting width

Sized right for golf courses, cities, schools. Small decks give excellent flexibility.

Sleek frame design, including single 
beam hitch and compact deck overlap

Design allows operator to make tighter turns without leaving windrows and skips. 
AFM virtually becomes a zero turn mower. (Oversized tires may not allow this.)

Automatic transport wing locks 

When wings are raised in the full transport position, the wings lock in place. No 
need to get off the tractor to lock. Pull rope from tractor seat to un-lock.

18" Transport tires 
with tapered roller bearings

Transport tires offer smooth roading and less grass compaction. Allows grass to 
stand up. Tapered roller bearings offer longevity.

Removable transportation tire spindles

Allows a spindle to be replaced by simply removing two bolts.

Back wheels on side decks even with 
transportation tires

Allows tighter turns without skips. 

Rigid rear side deck tires.

Rigid wheel yokes holds hills and slopes better. Safer unit than the competition.

13" Deck tires with sealant 

13" Tires offer great flotation, less lbs. per square inch. Sealant minimizes flats.

1/4" (0.63cm) Gauge wheel arms

Gives the mower gauge wheel arms a great deal of “hidden” strength.

Low pivot points on deck

The lower the pivot points are to the ground, the more side to side swing, allowing 
for excellent flotation from each deck.

Deflectors built into mower decks

Safety features meet ANSI standards. Many competitors use chains for protection. 
Once chains are removed the unit does not meet ANSI specifications.

Rear discharge 

Even dispersal, discharged items are aimed downward. No rear chains are needed, 
which tend to clump damp grass.

Rounded front deck edges 
with no protruding skid shoe

Helps protect trees and other obstacles.

5/16" (0.79 cm) Front edge and 
all-welded seams

Provides extra durability.

Cat. 3 Constant velocity main driveline

Constant velocity main driveline allows for tighter turns without harming U-joints in 
driveline, includes slip clutch.

Slip-clutch protection

Guards against premature gearbox failure. Protects mower deck spindles.

Cat. 2 wing drivelines

Reduces start-up torque that is put on the driveline, gearbox and gearbox support.

ABS guards

No paint to scratch off, lighter weight, no rattling or rust.

Heavy gearbox mounts on center 
and side mower decks 

Handles start-up torque better.

Gearbox Horsepower Rating

30 -65 horsepower (22-48 kW)

Gearbox warranty

5 years on parts and labor. 
Demonstrates our confidence in the gearbox’s quality and lasting performance.

Easy to grease blade spindles 

No guards to remove for routine greasing of blade spindles.

Middle spindle sits towards 
the back of the mower deck.

Uses less horsepower and allows material to escape the mower deck easier. The 
discharge of material is more even. Design eliminates windrowing.

Spring loaded idlers

Applies constant tension to belt to run efficiently.

Easy belt tension release 

Easily release belt tension for changing belt or for winter storage.

High blade tip speed
16,260 fpm (4956 m/min)

Lifts grass up for a clean cut and efficient discharge of material. 
Tip speed rates are as high or higher than the competition.

Choice of Blade
(Medium lift standard)
Others available thru parts dept.

Low Lift

 - Highly recommended in sandy soils where lifting isn’t crucial. Disturbs 

the soil very little, allowing blades to wear longer.

Medium Lift

 - Medium suction for lifting grass. Requires less horsepower than high 

lift.

High Lift

 - Greatest suction for lifting grass before cutting. Can take higher 

horsepower in tall dense grass. Not recommended in sandy soils.

Mulching

 - Perfect for leaf mulching.

Optional Hydraulic Operated Transport 
Locks

Transports locks can be released easily from the tractor seat while operating the 
same tractor control lever that raises and lowers the mower decks. Eliminates 
pulling a rope to release transport locks.

Section 7: Features & Benefits

Summary of Contents for 315-507M



























































Reviews: