Land Pride 315-507M, Operator'S Manual

Page: 23 / 58

Section 1: Assembly & Set-up
Table of Contents
AFM4211 All-Flex Grooming Mower 315-507M 3/8/23
19
4. If needed, attach driveline to the gearbox input shaft:
a. Pull back on inner driveline yoke lock collar and
slide yoke over the mower’s gearbox input shaft.
b. Release lock collar and continue to push yoke
onto the gearbox input shaft until pull collar snaps
in place.
5. Attach driveline to the power take-off shaft:
a. Pull back on outer driveline yoke lock collar and
slide yoke over the tractor’s power take-off shaft.
b. Release lock collar and continue to push yoke
onto the power take-off shaft until pull collar snaps
in place.
c. Move driveline back and forth to ensure both ends
are secured. Reattach any end that is loose.
6. Continue with
“Hydraulic Hook-Up”
below.
Hydraulic Hook-Up
Figure 1-4
Hydraulic Hook-Up
Refer to Figure 1-4:
This mower is equipped and plumbed from the factory
with double acting cylinders, hydraulic hoses, and
couplings for folding the wings and center deck.
1. Cut plastic ties securing hydraulic hoses (#1) to hose
support loop (#2). Be careful not to cut plastic tie
securing the ten linchpins (#5) to the support loop.
2. Route hoses (#1) through hose support loop (#2) and
connect to tractor remote outlets. Quick disconnect
hydraulic fittings for your tractor are supplied
attached to the hoses.
3. Locate carbon steel wire (#3) attached between wing
cylinders (#4). This wire secures the wing decks in
the folded position during shipment. Remove wire
and dispose of it in a trash container.
26622
Hook-Up Transport Lights
Refer to Figure 1-4:
The lead wiring harness (#6) is equipped with a
7-way round pin connector for connecting to the tractor’s
7-pin electrical outlet shown in Figure 1-1 on page 16.
1. Route lead wire harness (#6) through spring hose
loop (#2) as shown.
2. Connect wire harness (#6) to the tractor’s 7-pin
electrical outlet.
Enhance Module Wire Connections For LED Lights
Figure 1-5
Refer to Figure 1-5:
3. Check LED lights to make certain they are operating
correctly.
4. It is best to have a second person available for this
operation. Start tractor and operate lights as follows:
a. Turn on head lights to verify red lights illuminate.
b. Turn on flasher lights to verify amber light are
blinking on and off.
5. If lights did not operate properly, recheck hook-up of
wire harness (#1, #2, & #4) to enhance module (#3).
•
Make sure connector (#1D) with a red wire is
connected to the right-hand wire harness (#1).
•
Make sure connector (#2D) with a yellow wire is
connected to the left-hand wire harness (#2).
•
Make sure connector (#3B) on the lead wire
harness (#4) is connected to connector (#3A) on
enhancer module (#3).
6. Check wire harness routing to make sure wires will
not be pinched as the decks are folded and unfolded
and while raising and lowering mower height.
7. Add cable ties to wire harness (#1, #2, & #4) as
needed to secure them in place.
8. Continue with “Pull Rope Hook-Up” on page 21.
70482
IMPORTANT: Connectors on wire harness (#1 & #2)
are labeled “Light” on one end and “Enhancer” on
the other end. Ends labeled “Light” connect to the
LED lights. Ends labeled “Enhancer” connect to
enhance module (#3).
IMPORTANT: Connector (#1D) has a Red wire and
connects to wire harness (#1) on the right side of the
implement. Connector (#2D) has a yellow wire and
connects to wire harness (#2) on the left side.