Lake People ANA-TOOL F830 User Manual Download Page 7

General Safety Instructions 

WARNING 

For your protection, please read the following: 

     

Water, Liquids, Moisture: 

This appliance should not be used near water or other sources of liquids. 

Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. 

Power Sources: 

The appliance should be connected to a power supply only of the type described in the operating instructions or 

as marked on the appliance. 

Grounding: 

Care should be taken that this appliance is operated only properly grounded. 

Power Cord: 

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon 

or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they 

exit from the appliance. 

This unit is equipped with a 3-pole mains cable with German 3-pin mains plug. 

On request these units may be delivered with a 3-pole mains cable with North American 3-pin mains plug. 

In some countries this unit must be operated with a mains cable, supplied by the owner. 

Please refer to the table below to connect a mains plug:

 

OVERVIEW: POWER CORD FUNCTION AND COLORS

 

Leiter / CONDUCTOR

 

Farbe

 

COLOR

 

Alternativ

 

Alternativ

 

L

 

Phase

 

LIVE

 

Braun

 

BROWN

 

Schwarz

 

BLACK

 

N

 

Null

 

NEUTRAL

 

Blau

 

BLUE

 

Weiss

 

WHITE

 

   E    

 

 

Erde

 

EARTH GND

 

Grün-Gelb

 

GREEN+YELLOW

 

Grün

 

GREEN

 

 

U.K. Mains Plug Warning: 

A moulded mains plug that has been cut off from the cord is unsafe. Discard the mains plug at a suitable disposal facility.  

NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP 

POWER SOCKET.  

Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from 

your local retailer. Replacement fuses are 13 amps and MUST be ASTA approved to BS 1362. 

Mains Fuse: 

The mains fuse of this appliance is soldered in place and only accessible from the inside !! 

A burnt fuse may be an indicator of internal problems and should be replaced during a qualified servicing or 

repairing works !!  

Switchable Power Supply, Multimode Power Supply: 

Connect this unit only to the power source indicated on the equipment rear panel to ensure safe operation !! 

This unit is provided with either an internally solderable mains supply of 115 / 230 V AC or 

a multimode power supply which covers the range of 90 ... 260 V AC. 

Service / Repair: 

To reduce the risk of fire or electric shock, the user should not attempt to service the appliance beyond that 

described in the operating manual. All other servicing or repair should be referred to qualified personal !! 

Electromagnetic Compatibility 

This unit conforms to the Product Specifications noted as 

Declaration of Conformity

 at the end of this manual. 

Operation is subject to the following conditions: 

 - this device may not cause harmful interferences 

 - this device must accept any interference received, including interference that may cause undesired operation 

 - this device must not be operated within significant electromagnetic field 

VOR DEM ÖFFNEN NETZSTECKER
ZIEHEN!! PULL MAINS BEFORE
OPENING!! AVANT D´OUVRIER
RETIREZ LA FICHE MALE!!

Summary of Contents for ANA-TOOL F830
















Reviews: