MOUNTING
To install the antenna using the ceiling bracket:
1.
Find the antenna bracket (77). Also, find two #6 phillips head screws (90)
and two #6 lock washers (89). Use the #6 hardware to secure the antenna
bracket to the antenna base (see Figure-1).
2.
Find the tile runner bracket (HK). Remove the 1/4" - 20 hex nut and flat
washer from the bracket's carriage bolt in preparation for mounting.
Discard the flat washer-this will not be used.
3.
Find the 1/4" lock washer (16). Insert the antenna bracket onto the
threaded end of the tile-bracket bolt (Figure-1). Install the 1/4"
lock washer and nut loosely-the halves of the tile bracket must slide
freely for final installation.
4.
Clamp the ceiling bracket onto the support runner and tighten the 1/4"
mounting nut using a 7/16" wrench or adjustable wrench. Secure the
coaxial cable along the support runner using tape or cable ties.
5.
If installing one antenna, attach the connector to the AP unit's Primary
antenna connection. If installing a diversity system, attach the leads
from the two antennas to the AP unit's
Primary
and
Secondary
jacks.
To install the antenna using the I-beam bracket:
1.
For I-beam installations, first install bracket plate (77) as described
in Step-1.Next, referring to Figure-1A, install I-beam clamp (80) to the
bracket plate using flat washer (04), lock washer (84), and short 1/4"-20
bolt (55). Tighten the clamp bolt to secure antenna in place on beam.
CONTENTS
BPXCHK
(hardware kit for suspended ceiling mounting).
Loosened Bracket
FIGURE 1
16
HK
77
90
89
Ceiling Support Runner
19
26
48
2 Places
2 Places
Ceiling mount uses the
BPXCHK hardware kit
CONTENTS
BPXPHK
(hardware kit for pole/mast mounting).
18
4 Places
2 Places
6 Places
05
Squeeze bracket onto
runner and tighten nut.
Pole mount uses the
BPXPHK hardware kit
FIGURE 2
MOUNTING (cont.)
To install the antenna using the pole mount bracket:
1.
Find the U-bolt (05), mast clamp (26), plus two 5/16" nuts (18) lock
washers (19) and (02) flat washers.
2.
At the top of the pipe, using a 1/2" wrench or adjustable wrench, secure
the U-bolt to the clamp using the hardware provided (see Figure-2).
3.
Find two more 5/16" nuts (18). Install these nuts by turning them down
against the nuts securing the U-bolt to the mast.
4.
Find two antenna clamps (48), plus two 5/16" lock washers (19) and
the two remaining 5/16" nuts (18).
5.
Sandwich the antenna between the two clamps at its base and slide
this assembly onto the U-bolt (Figure-2). Secure in place using
hardware provided.
6.
Secure the coaxial cable along the mast or pole using tape or cable
ties.
7.
If installing one antenna, attach the connector to the AP unit's Primary
antenna connection. If installing a diversity system, attach the leads
from the two antennas to the AP unit's
Primary
and
Secondary
jacks.
FIGURE 1A
55
80
84
04
K E Y
P /N
DIS P L A Y
DE S C
S IZE
Q T Y
18
010118
S S HE X NUT
5/16” x 18 (00.0)
6
19
010119
S S L O C K
5/16” x (00.0)
4
WAS HE R
05
010405
U-B O LT
–
1
26
195726
V-B R AC K E T
–
1
48
195548
B AS E
–
2
B R AC K E T
02 013402 F L AT WAS HE R 5/16 2
K E Y
P /N
DIS P L AY
D E S C
S IZE
Q TY
H K S 2403B H H K
GR ID B R AC K E T
–
1
16
010216
INT. TO O T H
1/4” (00. 0
)
1
L O C K W AS H E R
77
195577
B R AC K E T
1
P L AT E
–
89
015589
INT. TO O TH
2
L O C K W AS H E R
#6
90
015590
S S MAC H IN E
#6-32 x 1/4”
P H IL L IP S S C R E W
80
194980
I-B E AM C L AMP
____
1
04
010104
F L A T W AS H E R
1/4”
1
84 010084 S P L IT L O C K 1/4 1
W AS H E R
55 015655 H E X H E AD B O LT
1/4 X 20 X 1/2 1
02
2 Places
2
Note:
for outside mounting or in wet environments,
make sure antenna is vertically mounted with weep holes
facing down.
