background image

Enhanced Class 1 Bluetooth v2.1 Module

 

Hardware Integration Guide 

Americas: +1-800-492-2320 Option 2 
Europe: +44-1628-858-940 
Hong Kong: +852-2923-0610 
www.lairdtech.com/bluetooth 

30 

CONN-HIG-BT740 

 

The following link provides a link to the Bluetooth Registration page: 

https://www.bluetooth.org/login/register/

   

 

For each Bluetooth Design it is necessary to purchase a Declaration ID. This can be done before starting the 
new qualification, either through invoicing or credit card payment. The fees for the Declaration ID will 
depend on your membership status, please refer to the following webpage: 

https://www.bluetooth.org/en-us/test-qualification/qualification-overview/fees

   

For a detailed procedure of how to obtain a new Declaration ID for your design, please refer to the following 
SIG document: 

https://www.bluetooth.org/DocMan/handlers/DownloadDoc.ashx?doc_id=283698&vId=317486

 

To start the listing, go to: 

https://www.bluetooth.org/tpg/QLI_SDoc.cfm

 

In step 1, select Reference a Qualified Design and enter the Declaration IDs of each subsystem used in the 
End Product design. You can then select your pre-paid Declaration ID from the drop down menu or go to the 
Purchase Declaration ID page, (please note that unless the Declaration ID is pre-paid or purchased with a 
credit card, it will not be possible to proceed until the SIG invoice is paid. 

Once all the relevant sections of step 1 are complete, complete steps 2, 3, and 4 as described in the help 
document. Your new Design will be listed on the SIG website and you can print your Certificate and DoC. 

For further information please refer to the following training material: 

https://www.bluetooth.org/en-us/test-qualification/qualification-overview/listing-process-updates

 

11.3

 

 Additional Assistance 

Please contact your local sales representative or our support team for further assistance:  

Laird Technologies Connectivity Products Business Unit  

Support Centre

http://ews-support.lairdtech.com

  

Email:  

[email protected]

  

Phone:  Americas: +1-800-492-2320 Option 2  

Europe: +44-1628-858-940  
Hong Kong: +852 2923 0610 

Web:  

http://www.lairdtech.com/bluetooth

  

 

 

Summary of Contents for BT740-SA

































Reviews: