Laguna Tools DAKE 33-672 Instruction Manual Download Page 3

 

 

Dake Corporation 

 

 

1809 Industrial Park Dr 

 

Grand Haven, MI 49417 

www.dakecorp.com

 

 

 

933672 

 

REV032022 

 

 

SAFEGUARDING THE POINT OF OPERATION 

ANSI B11.2 - Hydraulic Power Presses - 

Safety Requirements for Construction, Care, and Use 

 

 

It is important that Dake press users have a clear understanding of their responsibility involving the care and 

use of their Dake hydraulic press, including point-of-operation safe guards. Dake strongly recommends that 

Dake press users obtain a copy of the current American National Standard Institute (ANSI) B11.2 standard, for 

a more complete understanding of their responsibilities.  

 

ANSI B11.2 states the following, relative to point of operation safeguarding: 

 

“Normally, only the employer (press user) can determine the requirements of the press productions system 

components, including the dies and methods for feeding. Therefore, the employer is ultimately responsible to 

designate and provide the point-of-operation safeguarding system.” 

 

The standard also discusses additional responsibilities of the employer. Some of the key responsibilities are: 

  The employer is responsible for the safety, use, and care of the hydraulic power press production system.  

  The employer is responsible to consider the sources of hazards for all tasks to be implemented on the 

hydraulic power press production system.  

  The employer is required to eliminate or control identified hazards in the scope of their work activity.  

  The employer is responsible for the training of personnel, caring for, inspecting, maintaining, and operating 

hydraulic press production systems to ensure their competence.  

  The employer is responsible to provide and ensure that point-of-operation safeguarding is used, checked, 

maintained, and where applicable, adjusted on every production operation performed on a press 

production system.  

 

  

 

A complete and current copy of the ANSI B.11.2 standard can be obtained by contacting the following: 

 

American National Standards Institute 

1430 Broadway 

New York, NY 10018 

 

AMT – The Association For Manufacturing Technology 

7901 Westpark Drive 

McLean, VA 22102 

 

 

Summary of Contents for DAKE 33-672


















Reviews: