background image

 

 

INSTRUCTIONS OF USE 

14 

 

 

3.  

3.3.

 

Lighting 

Use  of  the  appliance  in  warm  weather 

(warm  days,  early  hours  of  the  afternoon 
on  sunny  days)  may  lead  to  lighting  and 
updraught problems. 

Certain weather conditions, such as fog, 

ice,  humidity  entering  the  flue,  etc.,  may 
hinder sufficient updraught in the flue and 
lead to suffocation. 

Proceed as follows in order to light  the 

appliance satisfactorily: 

 

Open the firebox door(s) and open 

all  the  firebox  air-intake  inlets  to  the 
full. 

 

Place  paper  or  a  firelighter  and 

some wood chips in the firebox.  

 

Light the paper or firelighter. 

 

Leave  the  door  slightly  ajar,  the 

width of two or three fingers, for about 
15 minutes until the glass warms up. 

 

The  first  time  the  appliance  is  lit, 

the  fire  should  be  gentle  to  allow  the 
parts of the appliance to dilate and dry. 

 

Important:

 The first time it is lit up, the 

appliance  may  give  off  smoke  and  strange 
smells.  This  is  not  a  cause  for  concern. 
Open  an  outdoor  window  to  ventilate  the 
room  during  the  first  few  hours  of 
operation. 

If  you  notice  water  around  the 

appliance,  this  is  produced  by  the 
condensation of the moisture in the  wood 
on  lighting  the  fire.  This  condensation  will 
no  longer  appear  when  the  appliance  has 
been  lit  three  or  four  times  and  has 
adapted to its flue. If it does not disappear, 
then  check  the  flue  draught  (length  and 
diameter  of  the  flue,  flue  insulation, 
airtightness) and the humidity of the wood 
used. 

3.4.

 

Safety 

Do  not  store  combustible  materials 

beneath the appliance. 

3.5.

 

Loading fuel 

In  order  to  load  firewood,  open  the 

firebox door gently, preventing the sudden 
entry  of  air  to  the  firebox  so  that  smoke 
does not enter the room that the appliance 
is installed in.  

Perform this operation with the glove to 

prevent burns to the hands.  

The maximum load height is 2 logs with 

diameters of approx. 10 cm. 

The  minimum  interval  between  loads 

for nominal heat output is 60 minutes. 

Always  load  with  the  nominal  amount 

(see table in section 1.1). 

For minimum burning (e.g. at night), use 

thicker logs. 

When  the  firebox  is  loaded,  close  the 

door. 

Be careful when placing logs in the firebox 

on appliances with vermiculite interiors. 
Vermiculite is a fragile material and may 

crack if knocked. 

 

 

 

 

 

 

 

 

 

3.6.

 

Operation 

The  appliance  should  be  operated  with 

the door. 

Summary of Contents for Tarbes





























Reviews: