manualshive.com logo in svg

Labnet Spectrafuge 16M, Service Manual, Page: 4 / 28

Share
Download
Labnet Spectrafuge 16M Service Manual Download Page 4

Section 1

Specifications

Maximum speed  ...............................................................................................  14,000 rpm ±5%

.

Maximum RCF  ..........................................................................................................  16,000 x g

Maximum capacity .......................................................................................  36 mL (18 x 2.0 mL)

Dimensions

Width  ..............................................................................................  209.5mm/8.25 in.

Depth  ...................................................................................................  226mm/8.9 in.

Height  ..................................................................................................  193mm/7.6 in.

Weight  .................................................................................................  5.1kg/11.2 lbs.

Noise level (with full rotor)  ....................................................................................  Approx. 56 dB

Electrical  Ratings

120V Version  .........................................................................  120V~, 50-60 Hz, 1.0A

                          Fuse 250V,2.5AT

230V Version  .........................................................................  230V~, 50-60 Hz, 0.5A

           Fuse 250V, 1.25AT

Ambient operating range  ...............................................................................  +2.0ºC to +40.0ºC

2

Summary of Contents for Spectrafuge 16M





























Reviews:

No comments