Labnet C2500 Instruction Manual Download Page 11

  Instruction Manual        | 

         9

 11.0  Limited  Warranty

Corning Incorporated (Corning) warrants that this product will be free from defects in material 
and workmanship for a period of one (1) year from date of purchase. CORNING DISCLAIMS ALL 
OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF 
MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. Corning’s sole obligation shall be 
to repair or replace, at its option, any product or part thereof that proves defective in material or 
workmanship within the warranty period, provided the purchaser notifies Corning of any such defect. 
Corning is not liable for any incidental or consequential damages, commercial loss or any other damages 
from the use of this product.

This warranty is valid only if the product is used for its intended purpose and within the guidelines 
specified in the supplied instruction manual. This warranty does not cover damage caused by accident, 
neglect, misuse, improper service, natural forces or other causes not arising from defects in original 
material or workmanship. This warranty does not cover motor brushes, fuses, light bulbs, batteries or 
damage to paint or finish. Claims for transit damage should be filed with the transportation carrier.

In the event this product fails within the specified period of time because of a defect in material or 
workmanship, contact Corning Customer Service at: USA/Canada 1.800.492.1110, outside the U.S. 
+1.978.442.2200, visit 

www.corning.com/lifesciences

, or contact your local support office.

Corning’s Customer Service team will help arrange local service where available or coordinate a return 
authorization number and shipping instructions. Products received without proper authorization will 
be returned. All items returned for service should be sent postage prepaid in the original packaging or 
other suitable carton, padded to avoid damage. Corning will not be responsible for damage incurred by 
improper packaging. Corning may elect for onsite service for larger equipment.

Some states do not allow limitation on the length of implied warranties or the exclusion or limitation 
of incidental or consequential damages. This warranty gives you specific legal rights. You may have other 
rights which vary from state to state.

No individual may accept for, or on behalf of Corning, any other obligation of liability, or extend the 
period of this warranty.

For your reference, make a note of the serial and model number, date of purchase, and supplier here.

Serial No.  __________________________________________ 

Date Purchased  _______________________________________

Model No.  _________________________________________ Supplier _____________________________________________

12.0  Equipment Disposal

According to Directive 2012/19/EU of the European Parliament and of the Council of 4 July 2012 
on waste electrical and electronic equipment (WEEE), this product is marked with the crossed-out 
wheeled bin and must not be disposed of with domestic waste. 

Consequently, the buyer shall follow the instructions for reuse and recycling of waste electronic and 
electrical equipment (WEEE) provided with the products and available at 

www.corning.com/weee

.

 

Summary of Contents for C2500













Reviews: