1a. Preparing Wall Fixings - Stud Walls
Tools required
1b. Preparing Wall Fixings - Concrete/Brick Walls
B
2. Removing the VESA TV Bracket from the TV Mount
G
4. Fixing the Back Plate of the Mount to the Wall Plate
5. Attaching the Wall Plate Covers
6. Attaching the VESA Bracket to the Television
7. Attaching the Television and VESA Bracket to the TV Mount
Technical Support:
www.philex.com/support
B
3. Positioning the Back Plate of the TV Mount on the Wall Plate
F
E
D
H
8. Adjusting the Tilt & Swivel
C
I
J
K
O
L
P
M
N
N
N
N
O
P
Fig.1
Fig.3
Fig.4
Fig.5
Fig.6
The wall bracket
A
is attached to the wall
using four appropriate screws/bolts as
shown in
Fig.3.
Make sure the screws/bolts
are suitable for wood and large enough to
support the weight of the TV and bracket
(if in doubt ask for advice at your local
DIY/hardware store and remember to make
sure that the heads of the screws/bolts are
the correct size to hold the bracket securely
in position).
Mark and drill four holes into the wood as close as
possible to the centre of the upright (you can use a stud detector to
find stud positions). To mark the holes, hold the bracket
A
to the wall, using a spirit level to make sure the bracket
is level, and mark the centre of each hole, see
Fig.1.
Drill the four holes and attach the bracket
A
to the wall
using the appropriate screws/bolts.
Fig.2
The process is the same as for attaching
to wood see
Fig.6.
You will however need to
use suitable screws/bolts/wall plugs
for the type of wall you are mounting
onto and for the weight of your TV and
bracket (if in doubt ask for advice at your
local DIY/hardware store and remember
to make sure that the heads of the
screws/bolts are the correct size to
hold the bracket securely in position).
When fixing to walls, screws/bolts
should be fixed into bricks/stone
not into mortar courses.
Lift the TV mount and
hook it onto the top rail
of the wall plate align
the holes of the
back plate with the
holes on the wall plate
in position
a
,
b
or
c
as preferred.
Select the centre
position
b
. if you are
unsure.
Slide the threaded retaining
brackets
D
into the
groove of the back plate
top and bottom aligning
the holes in the brackets
with the holes in the
wall plate and back plate
as shown.
Push the bolts
E
through
the washers
F
, the wall
plate and back plate
and screw them into the
threaded holes in the
retaining brackets
D
using the Allen key
H
provided.
Select the correct size bolts
to fit the VESA holes for
your TV
I
/
J
/
K
/
L
/
M
.
Attach the VESA bracket
to the back of the TV by
lining up the VESA holes and
using bolts
I
/
J
/
K
/
L
/
M
the washers
N
and the
spacers
O
and or
P
(if the bolts are too long or
the TV has a curved surface)
to fix the TV securely
to the adaptor brackets.
N.B. Always ensure that all
4 bolts engage well into the
VESA threaded apertures on
the back of your TV.
To o S ho rt
To o l o ng
(≥70% of depth)
Loosen the nuts holding
the VESA TV bracket to the
TV mount. unscrew the
bottom nuts.
Lift and remove the VESA bracket
as shown, keep the bottom
nuts in a safe place.
Engage the top nuts left on the VESA
bracket with the slots on the TV mount
and replace the bottom nuts then tighten
all four nutsas shown.
Clip the top and bottom wall
plate covers
C
onto the wall
plate.
Press down the tilt lever
to adjust the angle ot tilt.
When the angle is as
you want it pull up the
tilt lever to lock the
screen in position.