IMPORTANT INFORMATION:
•
This product is a label rewinder. It is only to be used to rewind labels of the
recommended dimensions and weight in an indoor, dry environment.
•
The machine has to be unplugged before any manipulation.
•
The machine is to be used on a flat surface, if the surface is not flat, it is to be fixed
using the holes in the base plate.
•
Do not leave the power cable in a passageway.
•
The ambient light of the working area needs to be sufficient to avoid any risk.
•
The rewinder can be used in ambient temperatures of +2°C to 40°C.
•
Connection of the machine to the power source must respect local and European
legislations.
SET-UP:
1.
Place the MC-11 so that the three (3) Rewind Fingers are perpendicular to the web of
the labels to be rewound. The MC-11 is bi-directional, and, can be operated in either
direction.
2.
Verify that the (ON-OFF-ON Direction) Switch on the rear of the MC-11 is in the OFF
(0) position.
3.
Insert the Power Supply Cord into the Power Socket on the rear of the MC-11.
4.
Plug the AC/DC Adapter into a suitable electrical outlet. The AC/DC Adapter can be
left plugged in at all times.
5.
The Rewinder has a combination Power and Direction (ON-OFF-ON Direction)
Switch on the rear panel. See the photo below. The Centre Position of the Switch is
"OFF" (0). To make the Rewinder run to the right (looking from the rear of the
Rewinder), press the Power / Direction Switch in the direction of the right arrow. To
make the Rewinder run to the left, press the Power / Direction Switch in the direction
of the left arrow.
FOR YOUR SAFETY:
Switch off device before any manipulation.
REWINDING LABELS:
Rewind labels onto any core from 25 up to 101mm diameter.
1.
Loosen the three (3) black Lock Levers on the back of the Core Holder Flange Plate.
2.
Grasp the front Flange Plate with one hand and the rear Flange Plate with the other.
Notice the rear Flange Plate has convenient cut-outs for your thumb.
3.
Rotate the Plates in opposite directions until the three (3) Core Fingers move to the
centre next to each other.
4.
Slide an empty cardboard core over the Fingers till close to the Flange Plate.
5.
Now rotate the Flange plates in the opposite direction to expand the Fingers against
the inside of the cardboard core. While you hold the Flanges so the Fingers are tight
against the inside of the Core, move one of the Locking Levers to the LOCK position.
NOTE: If one or more of the Locking Levers is up against the Hub and won’t lock,
pull up on the Lever (away from the Flange Plate) and reposition it.
6.
Now move the other two (2) Locking Levers to the LOCK position.
7.
Slide the cardboard core all the way up against the Flange Plate.
8.
Pull the label web to the cardboard core and use a piece of tape to secure the label
web.
9.
Adjust the position of the MC-11 if necessary so it is square with the label path.
10.
If you are using the APG-MC Adjustable Paper Guide, move the Arm into position to
guide the outer edge of the labels and lock it into place.
11.
Place the MC-11 (ON-OFF-ON Direction) Switch to the ON position in the desired
direction of operation, left or right.
12.
Start the printer and observe that the labels are being
rewound correctly. You can adjust the speed/torque
by turning the potentiometer on the upper part of the
machine to provide more, or less, rewind force as
desired.
13.
When rewinding is finished, place the MC-11 (ON-
OFF-ON Direction) Switch to the OFF (0) position.
14.
If the APG-MC Adjustable Paper Guide is in use, unlock and move the Arm out of the
way.
15.
Slide the cardboard core and the wound labels off the MC-11. You do not need to
loosen the three (3) Locking Levers unless you want to use a different diameter core.
WARNING!
This Product is for indoor use only.
Not for use in wet locations.
