LABEL INFORMATION AND MOUNTING
Labels should be wound on 3” cores with the core extending all the way to
the edge of the roll. Any “label out” copy position is acceptable.
The copy position for printed labels is number 3 (recommended) or 4 (
see
Diagram 1). This determines which way the label dispenses off of the roll
and also which direction you will put the bottle into the machine. Copy 3
allows the neck of a wine bottle to hang over the left side of the machine
as shown in the picture on the cover of this User Manual.
Labels must be die-cut with approximately 1/8” gap. Narrow labels will
work but the backing paper for them must be at least 1-1/2” inch width.
There are two 11” long, 1/16” aluminum roll guides and a tension spring
included with the machine. These guides should be placed on either side
of the roll of labels between the metal core inserts and the locking collar.
The notches on the end of the guide slide onto the chrome rod at the
bottom of the machine.
The Tension spring goes between the right roll guide and the locking collar
on the right side of the roll of labels as shown in diagram 2.
Note:
The aluminum roller at the front of the machine is attached with a
screw and nut to the mounting blocks on either side of the roller. Save the
screws for securing the roller assembly. The nuts are installed for shipping
purposes only and can be discarded.
THREADING THE LABELS
~Please Refer to Diagram 3~
1. Pull locking assembly “E” forward until it swings freely.
2. With labels facing down, unroll about 2 feet (600 mm.) of the labels and
bring them under label drive roller “B”, which is located in the middle of the
machine. Thread the labels
between
the top and bottom dispensing ta-
bles “D” & “E” and then back towards the label roll. Make sure that the la-
bels are over the label sensor lever “C” located behind the front rubber
roller. If needed loosen the thumbscrews on either side of label roll and
slide the roll to the proper position then re-tighten the thumbscrews.
3. Thread the labels under the locking assembly “A” and over label drive
roller “B”.
4. Put slight tension on the labels by pulling them towards the back of the
machine and STRAIGHT over the roll of labels.
5. While keeping tension on the labels pivot the locking assembly “A”
towards the back of the machine until it
“SNAPS”
in place over label drive
roller. You may need to push hard, but it will “
snap
” when it is locked.
6. Power on machine. Tap the foot-switch until a label dispenses every time
you tap it. If labels continue to feed without stopping, or if a label only
partially feeds past the label sensor then stops, a label sensor adjustment
is needed.
LABEL SENSOR ADJUSTMENT
ONLY IF STEP 6 FAILS! SENSOR ADJUSTMENT DOES NOT AFFECT PLACEMENT!
7.
SIDE TO SIDE adjustment only
: Simply loosen thumbscrew and slide sen-
sor left/right to desired position, tighten thumbscrew. CONTINUE TO STEP
8!
8. While thumbscrew is
tight
, reach under front of machine and grasp label
sensor housing. Pull sensor
housing
towards the Feed Drive Roller until the
small metal lever “C” is away from dispensing table “D”, now carefully and
SLOWLY push housing towards dispensing table “D” until lever
just
makes
contact with dispensing table and then STOP!
MAKE SURE NOT TO OVER
ADJUST
. If you continue to adjust the sensor towards the dispensing table
“D” after it makes contact, (causing the sensor to Pre-Load) the machine will
continue to feed labels without stopping.
HORIZONTAL ADJUSTMENT
Adjusting horizontal placement of the labels on the object can be done 2
different ways:
1. You can simply adjust the bottle guide in the front to apply the label where
you need.
2. You can slide the labels side to side, but this may require a sensor
adjustment if the labels no longer are contacting the label sensor, then
refer to step 7.
DUAL LABEL OPTION - FRONT TO BACK SPACING ADJUSTMENT
If you purchased a BM-910P-2 or BM-1510P-2:
1. Flip (1-label 2-label) toggle switch to down position for two label application.
2. Measure the circumference of the bottle.
3. Measure the total length of both labels (include the gap between labels on
the roll)
4. Subtract the total label length from the circumference and divide by 2.
Example:
If your circumference is 9.42” and your labels total 5” then
9.42” – 5” = 4.42” divided by 2 = 2.21 (set the display to 2.21). You may have to
make minor adjustments to achieve best results. The display reads from left to
right as follows: Inches, Tenths of an Inch, and Hundredths of an Inch
(hundredths of MMs, tenths of MMs, and MMs). Each position on the display has
its own button below it. The position will read from 0-9 and then back to 0.
OPTIONAL WASTE REWINDER
If your machine has the optional “Waste Re-Winder” after following previous
steps, take the waste paper back and over the take up spool, put your spring clip
on (be sure not to push clip against frame).
LABEL INFORMATION AND MOUNTING
Labels should be wound on 3” cores with the core extending all the way to
the edge of the roll. Any “label out” copy position is acceptable.
The copy position for printed labels is number 3 (recommended) or 4 (
see
Diagram 1). This determines which way the label dispenses off of the roll
and also which direction you will put the bottle into the machine. Copy 3
allows the neck of a wine bottle to hang over the left side of the machine
as shown in the picture on the cover of this User Manual.
Labels must be die-cut with approximately 1/8” gap. Narrow labels will
work but the backing paper for them must be at least 1-1/2” inch width.
There are two 11” long, 1/16” aluminum roll guides and a tension spring
included with the machine. These guides should be placed on either side
of the roll of labels between the metal core inserts and the locking collar.
The notches on the end of the guide slide onto the chrome rod at the
bottom of the machine.
The Tension spring goes between the right roll guide and the locking collar
on the right side of the roll of labels as shown in diagram 2.
Note:
The aluminum roller at the front of the machine is attached with a
screw and nut to the mounting blocks on either side of the roller. Save the
screws for securing the roller assembly. The nuts are installed for shipping
purposes only and can be discarded.
THREADING THE LABELS
~Please Refer to Diagram 3~
1. Pull locking assembly “E” forward until it swings freely.
2. With labels facing down, unroll about 2 feet (600 mm.) of the labels and
bring them under label drive roller “B”, which is located in the middle of the
machine. Thread the labels
between
the top and bottom dispensing ta-
bles “D” & “E” and then back towards the label roll. Make sure that the la-
bels are over the label sensor lever “C” located behind the front rubber
roller. If needed loosen the thumbscrews on either side of label roll and
slide the roll to the proper position then re-tighten the thumbscrews.
3. Thread the labels under the locking assembly “A” and over label drive
roller “B”.
4. Put slight tension on the labels by pulling them towards the back of the
machine and STRAIGHT over the roll of labels.
5. While keeping tension on the labels pivot the locking assembly “A”
towards the back of the machine until it
“SNAPS”
in place over label drive
roller. You may need to push hard, but it will “
snap
” when it is locked.
6. Power on machine. Tap the foot-switch until a label dispenses every time
you tap it. If labels continue to feed without stopping, or if a label only
partially feeds past the label sensor then stops, a label sensor adjustment
is needed.
LABEL SENSOR ADJUSTMENT
ONLY IF STEP 6 FAILS! SENSOR ADJUSTMENT DOES NOT AFFECT PLACEMENT!
7.
SIDE TO SIDE adjustment only
: Simply loosen thumbscrew and slide sen-
sor left/right to desired position, tighten thumbscrew. CONTINUE TO STEP
8!
8. While thumbscrew is
tight
, reach under front of machine and grasp label
sensor housing. Pull sensor
housing
towards the Feed Drive Roller until the
small metal lever “C” is away from dispensing table “D”, now carefully and
SLOWLY push housing towards dispensing table “D” until lever
just
makes
contact with dispensing table and then STOP!
MAKE SURE NOT TO OVER
ADJUST
. If you continue to adjust the sensor towards the dispensing table
“D” after it makes contact, (causing the sensor to Pre-Load) the machine will
continue to feed labels without stopping.
HORIZONTAL ADJUSTMENT
Adjusting horizontal placement of the labels on the object can be done 2
different ways:
1. You can simply adjust the bottle guide in the front to apply the label where
you need.
2. You can slide the labels side to side, but this may require a sensor
adjustment if the labels no longer are contacting the label sensor, then
refer to step 7.
DUAL LABEL OPTION - FRONT TO BACK SPACING ADJUSTMENT
If you purchased a BM-910P-2 or BM-1510P-2:
1. Flip (1-label 2-label) toggle switch to down position for two label application.
2. Measure the circumference of the bottle.
3. Measure the total length of both labels (include the gap between labels on
the roll)
4. Subtract the total label length from the circumference and divide by 2.
Example:
If your circumference is 9.42” and your labels total 5” then
9.42” – 5” = 4.42” divided by 2 = 2.21 (set the display to 2.21). You may have to
make minor adjustments to achieve best results. The display reads from left to
right as follows: Inches, Tenths of an Inch, and Hundredths of an Inch
(hundredths of MMs, tenths of MMs, and MMs). Each position on the display has
its own button below it. The position will read from 0-9 and then back to 0.
OPTIONAL WASTE REWINDER
If your machine has the optional “Waste Re-Winder” after following previous
steps, take the waste paper back and over the take up spool, put your spring clip
on (be sure not to push clip against frame).
