background image

9

1)  GENERAL DESCRIPTION

The EVOLUS automation electric lock is available in 3 models, which have different behaviour during a power failure.

                                                         

SLIM ELECTRIC LOCK for automation

SLIM ELECTRIC LOCK for automation

EVOLUS

EVOLUS

a)  “EV-EBSFSA” FAIL SAFE

In the case of a power failure, main power supply and emergency battery power, the electric lock 
will free the leaves, which can then be moved manually.

b)  “EV-EBSFSE” FAIL SECURE

In  the  case  of  a  power  failure, 
emergency battery power, the electric lock will keep the leaves 
blocked.

main  power  supply  and 

c)  BISTABLE “EBSBIS”

In the case of a power failure, 

 emergency battery power, the electric lock 

will remain in its current position.
Therefore, the leaves are free if the electric lock was not activated, or will remain blocked if the 
electric lock was activated.

main power supply and

2) POSITIONING and ELECTRIC CONNECTION               

The  dimensions  for  fastening  the  electric  lock  on  the  automation  are  specified  in  the 
EVOLUS Rel.1.6 Operator Installation Manual (Paragraph 2.3).
The electric lock is fastened to the automation by 2 M6 X 10 screws on M6 nuts, which are 
located in the special lower slot in the transom.
The sliding carriages must be regulated so that when the leaf is in the closed position, the 
electric lock lever can hook to the carriage bracket and keep the leaves blocked.

The electric lock kit includes a power supply cable. This cable has two wires on one end that are connected to the electric lock 
solenoid wires with the specific terminals. The other end of the cable has a connection that is inserted in the LOCK1 connector on the 
Evolus operator electronic control unit.
If the bistable electric lock EV-EBSBIS is installed, there will be a second power cable. One end of it must be connected to the 
secondary solenoid cables (LOCK2) of the electric lock and the other end must be connected to the LOCK 2 output on the electronic 
control unit where the connector is located. 

Electric locks are supplied in Kit, including coupling brackets 
and fastening accessories.

GB

Summary of Contents for EVOLUS

















Reviews: