Labconco CentriVap Complete 73150 Series User Manual Download | Manualshive

Page: 26 / 37

background image

Chapter 6: Accessories for Your CentriVap Complete

Product Service 1-800-522-7658

22

Original instructions

PART #

DESCRIPTION

7461900

7461901*

Rotor (96 well plate)
Holds (4) Standard 96 well plates or
(2) Deep well 96 well plates

7460900

Clear Canister – Accommodates inserts listed below

7814800

Acid Trap Insert

7814900

Moisture Trap Insert

7995600

Ammonia Trap Insert

7815000

Radiochemical Trap Insert

7815200

Solvent Trap Insert

Installing a Vacuum Gauge

A user-supplied vacuum gauge may be attached to the CentriVap to monitor the
vacuum level. Attach the vacuum gauge to the barb end of the Quick Disconnect
Coupling fitting that was supplied with the CentriVap using a length of suitable
rubber hose. The Quick Disconnect Coupling fitting can then be pushed into the
mating connector on the rear left side of the CentriVap. The Quick Disconnect
Coupling fitting can be removed from the mating connector by pressing on the tab
on the connector and then pulling out the Quick Disconnect Coupling fitting.
Always remove the Quick Disconnect Coupling from the CentriVap when a
vacuum gauge is not attached to it.

USER SUPPLIED
VACUUM TUBING

«
...
24
25
26
27
28
...
»

Summary of Contents for CentriVap Complete 73150 Series






































Reviews:

No comments

Related manuals for CentriVap Complete 73150 Series

Brand: Sagola Pages: 8

Brand: Obdstar Pages: 10

Brand: NEC Pages: 44

Brand: CAIRE Pages: 2

Brand: Olsen Pages: 56

Brand: Waterous Pages: 5

Brand: 3TECH Pages: 32

Brand: 4EVAC Pages: 15

Brand: Bacharach Pages: 48

Sportsound SSR-200

Brand: Daktronics Pages: 5

Brand: Xebex Fitness Pages: 15

Brand: qeedo Pages: 2

Brand: Parker Pages: 39

Brand: Water Witch Pages: 2

Brand: Falltech Pages: 48

Brand: Tascam Pages: 8

Brand: R&S Pages: 371

Brand: R.M. Young Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands