Lab.gruppen PLM 12K44 Quick Start Manual Download Page 28

16. Warranty and support 

28    

PLM+ SERIES  Quick Start Guide  rev 1.0.0

16. Warranty and support 

16.1. General 

This product is manufactured by Lab.gruppen, and it is warranted to be free from any defects caused by 
components or factory workmanship, under normal use and service, for a period of six (6) years from date of 
purchase from an authorized Lab.gruppen dealer. If the product fails to perform as specified during the warranty 
period, Lab.gruppen will undertake to repair, or at its option, replace this product at no charge to its owner, 
provided the unit is returned undamaged, shipping prepaid, to an authorized service facility or to the factory. 
This warranty shall be null and void if the product is subjected to: repair work or alteration by a person other 
than those authorized by us; mechanical damage including shipping accidents; war, civil insurrection, misuse, 
abuse, operation with incorrect AC voltage; incorrect connections or accessories; operation with faulty associated 
equipment; or exposure to inclement weather conditions. Damage due to normal wear and tear is not covered 
by the warranty. Units on which the serial number has been removed or defaced will not be eligible for warranty 
service. Lab.gruppen shall not be responsible for any incidental or consequential damages. Lab.gruppen’s 
responsibility is limited to the product itself. Lab.gruppen takes no responsibility for any loss due to cancellation 
of any events, or rent of replacement equipment or costs due to a third party’s or customer’s loss of profit, or any 
other indirect cost or losses however incurred. Lab.gruppen reserves the right to make changes or improvements 
in design or manufacturing without assuming any obligation to change or improve products previously 
manufactured. This warranty is exclusive, and no other warranty is expressed or implied. This warranty does not 
affect the customer’s statutory rights. 

International Warranties

Please contact your supplier or distributor for this information, as rights and disclaimers may vary from country 
to country.

16.2. Technical assistance and service

16.2.1. International service

If your Lab.gruppen product requires repair, contact your Lab.gruppen dealer or distributor, visit  
http://labgruppen.com/support/find_service_centre/ or contact Lab.gruppen by phone or email to obtain details 
for the nearest authorized service center.

Summary of Contents for PLM 12K44

































Reviews: