background image

 

 

4

 

3. Important Safety Information & General Precautions from the 
Manufacturer  

 

 

 

Warning  

 

Equipment contains dangerous voltages and can be hazardous if installed or operated incorrectly. 
Non-compliance with warnings or failure to follow the instructions contained in this manual can 
result in loss of life, severe personal injury or serious damage to property. 
Some procedures in this manual require the power for the equipment to be turned off and isolated.  
Turn the power OFF at the power point and unplug the power supply lead by the plug body.   
 

 

 

 

 

Failure to do so may result in electric shock

 

 
This manual provides instructions for the safety, operation & installation for the SWIFT GRINDER

  

 

  Read & understand all instructions that appear in this manual prior to the installation & 

operation of the equipment. 

  Do not operate this equipment if it has a damaged cord or plug, if it is not working properly, or if 

it has been damaged or dropped. 

  Train all staff on the operation of the equipment and verify ability. 

  Do not hose down or splash water on the equipment. 

  Qualified and skilled personnel only should service this equipment. Contact the Supplier for 

repair or advice. 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for SWIFT EPSB

































Reviews: