background image

iii 

 

Unit Location 

 

 

Allow at least 6 inches of free air on all vented surfaces for proper cooling. 

 

Do not operate this unit in a closed-in area or restrict ventilation in any way. 

 

Do not set any battery on top of this unit. 

 

Never allow battery electrolyte to drip on this unit when reading the specific gravity or filling the battery. 

 

Never  place  this  unit  directly  above  a  standard  flooded  battery.  Gases  from  the  battery  will  corrode  and 
damage equipment.   

 

A sealed maintenance free or valve regulated lead acid (VRLA) battery may be placed below this equipment. 

 

Check for Damages 

 
Prior to unpacking the product, note any damage to the shipping container. Unpack the product and inspect the 
exterior  of  product  for  damage.  If  any  damage  is  observed,  contact  the  carrier  immediately  and  contact  La 
Marche  for  advice  on  the  risk  due  to  any  damage  before  installing  the  product.  Verify  that  you  have  all  the 
necessary parts per your order for proper assembly. 
 

CAUTION:

 Failure to properly file a claim for shipping damages, or provide a copy of the claim to La 

Marche, may void warranty service for any physical damages reported for repair. 
 

Returns for Service 

 
Save the original shipping container. If the product needs to be returned for service, it should be packaged in its 
original shipping container. If the original container is damaged/unavailable, make sure  the  product is packed 
with  at  least  three  inches  of  shock-absorbing  material  to  prevent  shipping  damage. 

  La  Marche  is  not 

responsible for damage caused by improper packaging of returned products. 

 

Inspection Checklist 

  

 

Enclosure exterior is not marred or dented. 

 

 

 

 

 

 

 

There are no visibly damaged components.  

 

 

 

All hardware and connections are tight.  

 

All wire terminations are secure. 

 

All items on packing list have been included. 

 

Handling 

 
Equipment can be very heavy and/or top heavy.  Use adequate manpower or equipment for handling. Until the 
equipment  is  securely  mounted,  care  must  be  used  to  prevent  the  equipment  from  being  accidentally  tipped 
over. 

Summary of Contents for A75R

















Reviews: