background image

 

 

17

2012/3/8Ver1.4+Ver1.1 

The scrolling text

AVERAGE SPEED =

, then

MLH=                    0.0

         

The scrolling text

CALORIES BURNT =

, then

KCAL=                0.0

           

The scrolling text

AVERAGE WATTS =

, then

WATTS=              0.0

         

The scrolling text

AVERAGE METS =

, then

METS=                    0.0

 

5-9.

 

Introduction of HR CONTROL mode: pre-set the heart rate control mode as 50W. 
When t signal of the heat rate is detected, console will judge the heat rate value once 
every 10 seconds. 

5-9-1.

 

During the exercise, the program will compare the actual value of heart rate 
with the target value of heart rate. The following is the way to judge the value of 
heart rate: 

When the actual heart rate value 

set heart rate value 15, WATT will 

automatically increase 20 with maximum as 400 WATT. 
When the actual heart rate value 

set heart rate value 5, WATT will 

automatically increase 10 with maximum as 400 WATT. 
When the actual heart rate value  set heart rate value 5, WATT will 

 

automatically decrease 10 with minimum as 50 WATT. 
When the actual heart rate value  set heart rate value 15, WATT will 

automatically decrease 20 with minimum as 50 WATT. 
When the actual heart rate value  set heart rate value 30, WATT will 

automatically decrease to 50WATT. While the actual heart rate value 

set 

heart rate value 5, the program will continue performing. 

5-9-2.

 

During exercise, if heart rate signal is not detected, the figure will display “NO 
PULSE”. The console will enter the PAUSE mode if no signal is detected after 
60 seconds. 

5-9-3.

 

When PRM is less than 40, Dot Matrix will display 

RPM

 and the console 

will enter PAUSE mode after 5 seconds. 

5-9-4.

 

HR CONTROL mode can be operated only with wireless heart rate.   

5-9-5.

 

During the program, Dot Matrix will show the following: the pre-set is Level 1. 
Up and Down keys cannot be used. 

 
 

6. 

WATT Mode

WATT CONTROL Mode 

6-1.

 

Under Start/Ready status, press WATT and the Dot Matrix will display

WATT

, the 

scrolling text will display PRESS ENTER TO BEGIN PROFILE.

from right to left. 

6-2.

 

Press ENTER key to change Target WATT, the scrolling text will display

ENTER 

WATT <25-400>

. You can set the value of Target WATT by the number keys 0~9 

and the scrolling text will display

WATTS=                  xxx

, the input value will be 

blinking. When you press 0-9 to set values, you should set 2 or 3 digits (range: from 
25 to 400).. After setting, press ENTER to confirm. 

6-3.

 

You can press ENTER to set time, the scrolling text will display

ENTER TIME <10 

Summary of Contents for DK900EAJ01AA



























Reviews: