LANGUAGE SETTING
The weekdays can be displayed in LCD2 with the pre-set languages: US English, French and Spanish.
1.
Set the desired language for the weekday display in LCD 2 by use of the
+
key.
2.
Press and release the
SET
key to enter the mode
“Manual Time Setting”
.
MANUAL TIME SETTING
In case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting distance, etc.), the time can be manually set.
The clock will then work as a normal Quartz clock.
Note
: In 12 hours mode the time will be displayed with an additional
“
PM
”
for the time from 12:00 noon until 11:59.
1.
The hour digits will start flashing on LCD1.
2.
Set the desired hours by pressing and releasing the
+
key followed by pressing the
SET
key.
3.
Now the minute digits will start flashing.
4.
Set the desired minutes by pressing and releasing the
+
key . If the
+
key is held, the units will increase by 5.
5.
Press and release the
SET
key to move to the
“Year Setting”
.
Note:
The unit will still try and receive the signal every day despite it being manually set. When it does receive the signal, it will change the
manually set time into the received time. During reception attempts the WWVB tower icon will flash. If reception has been unsuccessful,
then the WWVB tower icon will not appear but reception will still be attempted the following hour.
WWVB time reception takes place from 12:00 am through 6:00 am each day (attempts WWVB reception every full hour within this time
frame). When the time signal is received for example at 1:00 am, the atomic clock will not attempt to receive the WWVB signal for the
remaining hours until 6:00 am. Therefore, the next signal attempt will take place between 12:00 am and 6:00 am the next day. The other
times WWVB reception takes place, are upon setup and after manual time set exiting mode. Reception is generally not possible during
daylight hours due to the interference of the sun.
YEAR SETTING
The year can be selected sequentially from 2000 to 2049 and will then start over again (default setting 2000). Only the last 2 digits of the
year will be visible on LCD2 .
1.
The year digits will start flashing on LCD2. Select the desired year by use of the
+
key.
2.
Press and release the
SET
key to switch to the
“Month Setting”
.
MONTH SETTING
1.
The month digits on LCD2 will start flashing. Set the desired month by use of the
+
key.
2.
Press and release the
SET
key to move to the mode
“Date Setting”
.
Date Setting
1.The digits for the date will start flashing on LCD2 (Default setting 1). Set the desired date by use of the
+
key.
Note:
The date can only be set in conjunction with the selected month. For example, it is not possible to set the date 30 if the month of
February is selected.
Press and release the
SET
key to enter the “
Weekday Setting
”.
WEEKDAY SETTING
1.
The weekday symbols will be displayed on LCD2 in the pre-set language and flashing. Set the desired weekday by use of the
+
key.
2.
Press and release the
SET
key to enter the mode
“12/24 Hours Time Display Setting”
.
12/24 HOURS TIME DISPLAY SETTING
1. The
“12h”
or
“24h”
will start flashing in LCD1 (Default setting 12h). Select the desired time display mode by use of the
+
key.
2.
Press and release the
SET
key to enter the
“ºC/ºF Temperature Setting“
.
°C OR °F TEMPERATURE SETTING
1. The
characters
“°C”
or
“°F”
will start flashing on LCD1 (Default setting °F). By use of the
+
key select
“°C”
for
temperature display in degrees Celsius or
“°F”
for degrees Fahrenheit.
2.
Press and release the
SET
key to exit the setting mode and switch back to the normal display mode .
EXIT THE MANUAL SETTING MODES
•
To return to the normal display mode from anywhere in manual setting mode simply press the
SNZ
key anytime.
•
If no keys are pressed for at least 15 seconds in setting mode, the atomic clock will automatically switch back to normal display mode.
ALARM SETTING
To enter into the alarm setting mode:
1. Hold
the
ALM
key for 4 seconds. The hour digits start flashing.
2.
Press and release the + key to set the hour.
3.
Press and release the
ALM
key to set the minutes. The minute digits start flashing.
4.
Press and release the + key to set the minutes.
5.
Press and release again the
ALM
key to exit the Alarm setting mode or wait for 15 seconds automatic timeout.
TO DEACTIVATE THE ALARM:
Alarm icon
(((
•
))) (ON)
The alarm will be automatically ON when the alarm time is set. To deactivate the alarm (OFF), press and release once the
ALM
key in
normal mode display. The alarm icon will disappear, the alarm is now off
SNOOZE SETTING
The snooze can only be activated during alarm time for a snooze duration of 10 minutes by pressing the SNZ key on the back of the clock
3
All manuals and user guides at all-guides.com