La Crosse Technology XG-20, Instruction Manual

Page: 13 / 115

8.1 Countdown Timer Mode -
Setting the Timer
8.0 Countdown Timer Mode -
Countdown Timer Mode
To Set the Countdown Timer
- Press and hold the [mode] button for 2 seconds to
change the display from Countdown Timer Mode to
Countdown Timer Setting Mode.
NOTE: The setting range of the timer: 0 to 99 hour, 59
minutes, 59 seconds.
- The second digits flash on the display because it is
being selected.
The Setting Procedure
- Press [mode] button to change the selection following
the Countdown Timer Setting Sequence.
- If the digits are flashing, press the [s ta rt /s to p] bu tt on
to increase the number; hold the [start/stop] button
to
change the number at a higher speed. Press the
[compass] button to
decrease the n um be r; ho ld th e
[compass] button to change the number at a higher
speed.
- After you set the timer, press the [mode] button to
exit the setting sequence.
- If no key-stoke has been activated for 30 seconds, the
setting display
w
ill return to Countdown Timer Mode.
Countdown Timer
- has
a
countdown feature: the Countdown
Timer Mode.
- T h e C o u n t d o w n Ti m e r s t a r t s c o u n t i n g f r o m t h e
preset
number to zero and stops at zero.
- T h e 1 s t r o w o f t h e d i s p l a y s h o w s t h e ' C d T '
indicator.
- The 2nd row of the display shows the countdown time:
hour, minute and second.
- T h e i n d i c a t o r s
around
t h e d i s p l a y s h o w s t h e
countdown time in 1 second.
XG-20
To Use the Timer
- W h e n t h e t i m e r i s s e t , p r e s s t h e [ s t a r t / s t o p ]
button to start the timer. Press the [start/stop] button
again to stop the timer.
- If the timer is started, the countdown time (hour, minute
and second) will be shown on the display continuously.
- The timer starts to beep every second when it is 5
seconds to the end of the countdown.
-
When the
countdown time
reaches
zero, a long beep
lasting for
2 seconds will be heard.
- Press any button in this period
to
terminate the
beep sound prematurely.
-
When
the countdown time
reaches
zero, press [compass]
b u t t o n t o r e - l o a d t h e p r e s e t t i m e , o r p r e s s
[start/stop] button to re-load the preset time and
start the countdown simultaneously.
To Reset the Timer
- Press and hold the [compass] button for 2 seconds to
reset the timer
while
the timer
i
s stopped.
.
Pacer Mode
- The XG-20
has a
build-in a pacer for the user:
The
Pacer Mode.
- The 2nd row of the display show the current pacer
setting.
- The ' PACE ' indicator will appear on the 3rd
row of the display.
- If the pacer is activated, the XG-20 will beep at
the preset rate (bpm) every minute.
To Start/Stop the Pacer
- If the Pacer has been set, press the [start/stop] button to
start the pacer. Press the [start/stop] button again to
stop the pacer (beeping sound).
8.2 Timer Mode - Using the Timer
9.0 Pacer Mode -
Pacer Mode
second minute
hour
Alarm Time Setting Sequence
hold
mode
mode
button
mode
button
mode
button
Increase
the number
increase the
number at
a higher speed
start/stop button hold start/stop
decrease
the number
decrease the
number at
a higher speed
hold
compass compass
button
hold
mode
Countdown Timer Setting Mode Countdown Timer
'running' Mode
Countdown Timer Mode Countdown Timer Mode
digits have been
selected (flashing)
digits have been
selected (flashing)
analog
second
analog
second
countdown
time Pre-set
countdown time
the countdown
time
the number
of bpm
(Beep per
minute)
Countdown
Timer Mode
indicator Countdown
Timer Mode
indicator
Pacer Mode
indicator
start/stop
hold mode
Pacer Setting Mode
Pacer Mode