background image

 

17

 
WARRANTY INFORMATION 
 

La Crosse Technology provides a 1-year warranty on this temperature clock.  Contact 
La Crosse Technology immediately upon discovery of any defects covered by this 
warranty. 
 
Before sending the temperature clock in for repairs, contact La Crosse Technology.  The 
temperature clock will be repaired or replaced with the same or similar model. 
 
This warranty does not cover any defects resulting from improper use, unauthorized 
repairs, faulty batteries, or the clocks inability to receive a signal due to any source of 
interference. 
 
LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL, 
CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED 
WITH THE OPERATION OR MALFUNCTION OF THIS TEMPERATURE CLOCK.  
THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR 
PUBLIC INFORMATION.  THIS PRODUCT IS NOT A TOY.  KEEP OUT OF 
CHILDRENS’ REACH. 
 
This warranty gives you specific legal rights.  You may also have other rights specific to 
your State.  Some States do not allow the exclusion of consequential or incidental 
damages; therefore the above exclusion of limitation may not apply to you. 
 
For warranty work, technical support, or information contact: 
 

La Crosse Technology 
1116 South Oak Street 

La Crescent, MN 55947 

Phone: 507.895.7095 

Fax: 507.895.8000 

 

e-mail: 

[email protected]

 

(warranty work) 

[email protected]

 

(information on other products) 

web: 

www.lacrossetechnology.com

 

 
 
 
 
 
 

Summary of Contents for WS-8011UM-TWC



















Reviews: