8
Backlight Options
When operating with the optional A/C power cord, the weather station backlight can be turned ON, OFF or automatic (depending on light
conditions).
•
AUTO: the backlight will be off in when there is adequate light, and will come on automatically in low light conditions.
•
ON: the backlight will be on constantly when using A/C power.
•
OFF: the backlight will remain off unless the LIGHT button is pressed.
Note:
For continuous backlight control the optional A/C adaptor (not included) must be plugged in.
Backlight sensor sensitivity can be adjusted to high or low using the switch, located on the back of the weather station.
When operating on battery power alone, the backlight can be activated for three seconds by pressing the LIGHT button
on top of the weather station.
Remote Sensor Status Icon
The wave icon above the channel 1 display shows the connection status of the remote sensor.
Activate Search for Remote Sensors
•
Hold the DOWN arrow button for 4–6 seconds to activate a search for all remote sensors.
Normally, the weather station will automatically find and display measurement results from the remote sensors. Occasionally other radio
transmission sources (TV, cordless or cell phones, etc.) can interrupt the sensor signal.
Memory Reset Procedure
Note:
This will completely reset all of the stored memory.
1.
Hold SNOOZE and UP
buttons for 4 seconds so the backlight will flash.
2.
Press the SET button which will clear the memory–the weather station will start beeping with a 1 second delay.
3.
Wait until the beeping stops.
4.
Disconnect weather station from the A/C adapter. Remove batteries from the back or the weather station (optional) if installed.
5.
Wait at least 10 seconds, and then reinsert the A/C adapter and batteries.
IMPORTANT: Do not
press any buttons during the setup process which take 5-15 minutes. During this time the weather station will
show the pressure icon and
inHg
(inches of mercury) flashing. Setup is completed when the weather station shows default settings for
pressure and altitude (sea level), indoor/outdoor temperature and humidity, wind and rain readings, etc.
6.
Follow the program menu to
set language
and
city code
then any custom settings desired.
Changing Batteries
The battery status of each remote sensor is checked every hour. If the low battery indicator lights up, replace the batteries in the
corresponding sensor.
•
Do Not Mix Old and New Batteries
•
Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries
Weather Station
With A/C power cord:
Connect the optional 7.5V A/C adaptor to the weather station to avoid losing any data.
•
Remove the battery compartment door at the back and replace all batteries.
•
Replace the battery compartment door.
Without A/C power cord:
•
Remove the battery compartment door at the back and replace all batteries.
•
Replace the battery compartment door.
•
Do not
press any buttons during the setup process, which takes 5-15 minutes. During this time, the weather station will show the
pressure icon and
inHg
(inches of mercury) flashing. Setup is completed when the weather station shows default settings for pressure
and altitude (sea level), indoor/outdoor temperature and humidity, wind and rain readings, etc.
•
Set language and city code.
Remote Sensor Batteries
•
Replace the batteries following the setup instructions for the corresponding sensor.
•
When the batteries are properly installed, the remote sensor will resume sending signals to the weather station.
•
Hold the DOWN
arrow button for 4–5 seconds on the weather station to search for the remote sensors.
Care and Maintenance
•
Do not immerse the sensors or weather station in water.
•
Do not clean the sensors or weather station with abrasive or corrosive materials that might scratch plastic parts or corrode electronic
circuits.
•
Do not subject the sensors or weather station to excessive force, shock, dust, temperature, or humidity, which may result in
malfunctions, shorter lifespan, damaged batteries, and damaged parts.
•
Do not tamper with the product’s internal components. Doing so will invalidate the warranty and may cause damage.
•
The product contains no user-serviceable parts.
•
Read the user's manual thoroughly before operating the product.
Searching Strong No Signal
