PROJECTION:
Battery Power:
Press and release the
SNOOZE/LIGHT button to
show the
projection for 10 seconds.
Note:
Projection will not display constantly when operating on battery power.
A/C Power
: Projection is displayed constantly unless turned off.
Note
: can be turned off see “
Backlight and Projection Intensity
”
Rotate Projection:
Press and release the PROJECTION button to rotate
projection image 90 degrees. Press and release the PROJECTION button again
to rotate another 90 degrees.
Change Projection Mode:
Hold, then release the PROJECTION button to switch
projection modes. Watch the projection image to view the changes.
o
Time and Outdoor Temperature:
alternate
every 5 seconds (default)
o
Time
: Hold and release PROJECTION button
o
Outdoor Temperature
: Hold and release PROJECT button again
USB CHARGE PORT:
The integrated USB charging port (on back) will charge devices when the Projection
Alarm is plugged into a power outlet.
Note:
This is a power output (charging) port only. This port will not supply power to
the Projection Alarm.
Connect your existing USB charging cord
for your external device to the USB
charging port on the back of the Projection
Alarm to begin to charge. Charging times
will vary.
Note:
Check that your device will charge
with the USB cord it came with.
Many
USB cords are for data transfer only, and
cannot be used for charging.
Output
: 0.5A maximum current USB.
Do NOT overload USB port.
IMPORTANT:
W hen operating on a/c power, the backlight, projection and USB
charging port will turn off while the Projection Alarm searches for the WWVB signal,
to avoid interference. The backlight and projection will return after the 2-10 minute
search (which occurs during the late night or early morning hours). Then the USB
charging port will resume working.
TEMPERATURE TREND ICONS:
The indoor and outdoor temperature trend indicators are updated every 30 minutes.
These trends represent temperature changes over the past three hours.
Temperature rising more than 2°F /1°C in the past three hours
Temperature has
not changed
more than 2°F /1°C in the past three
hours
Temperature falling more than 2°F /1°C in the past three hours
The temperature trend indicators are shown next to the indoor temperature and
outdoor temperature readings.
POSITIONING OUTDOOR TRANSMITTER:
Once the Projection Alarm displays the outdoor temperature, place it and the
transmitter in the desired locations and wait approximately 1-hour before
permanently mounting the transmitter to ensure that there is proper reception. The
transmitter should be mounted vertically, in a shaded, protected area, at least 6 feet
from the ground to avoid damage and ensure accurate readings. The transmitter is
water resistant, not waterproof and should not be placed anywhere it will become
submerged in water or subject to standing water or snow.
WALL MOUNT
Choose a shaded location (under an overhang) for the transmitter
that is within the confirmed wireless reception range of the
Projection Alarm for accuracy.
Install one mounting screw (not included) into a wall leaving
approximately ½ of an inch (12.7mm) extended.
Place the hanging hole (on the back of the transmitter) onto the
mounting screw and gently slide the transmitter down onto the
mounting screw to secure it into place.
IMPORTANT:
For true temperature readings, mount the transmitter out of direct
sunlight on a North-facing wall or in any other well shaded area like under an eave
or deck rail. The maximum transmitting range in open air is over 200-feet (60
meters). Obstacles such as walls, windows, stucco, concrete, and large metal
objects can reduce the range. Place the transmitter at least 6 feet in the air to
improve signal transmission.
LOW BATTERY:
When this icon appears in the indoor (IN) reading section, replace the batteries
in the Projection Alarm.
When this icon appears in the outdoor (OUT) readings section, replace the
batteries in the outdoor transmitter.
CARE AND MAINTENANCE:
Do Not Mix Old and New Batteries
Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries
Do not expose the Projection Alarm to extreme temperatures, vibration or shock.
Keep Projection Alarm dry.
Clean the Projection Alarm with a soft damp cloth. Do not use solvents or scouring
agents.
The Projection Alarm is not a toy. Keep it out of reach of children.
The Projection Alarm is not to be used for medical purpose or for public
information, but is determined for home use only.
The specifications of this product may change without prior notice.
Improper use or unauthorized opening of housing will void the warranty.
If the Projection Alarm does not work properly, change the batteries and/or check
the a/c cord connection.
SPECIFICATIONS:
Indoor
:
Temperature Range:
+32°F to +122°F (0°C to 50°C)
Accuracy:
+/- 2 degrees Fahrenheit
Interval:
About every 30 seconds
Outdoor
:
Temperature Range:
-40°F to 140°F (-40°C to 60°C)
Alkaline Batteries: -20°F to 140°F (-28.8°C to 60°C)
Lithium Batteries: -40°F to 140°F (-40°C to 60°C)
Temperatures below - 20°F (-28.8°C) require Lithium
batteries in the outdoor transmitter.
Distance:
Over 200 ft. (60 meters) RF 433MHz (open air)
Interval:
About every 30 seconds
Power:
Projection Alarm:
5-volt a/c power adapter (included)
Optional 2-AAA, IEC, LR3 batteries (not included)
TX14 Transmitter:
2-AA, IEC, LR6 batteries (not included)
Battery Life:
TX14 Transmitter Battery Life:
Battery life is over 24 months when using reputable
battery brands for both Alkaline and Lithium batteries
Projection Alarm Battery Backup:
Battery life is over 24 months when using the AC
adapter for primary power
USB:
Output:
0.5 Amp maximum current
Dimensions:
Projection Alarm:
5.23” L x 1.96” W x 4.33” H (133 x 50 x 110 mm)
TX14 Transmitter:
2.5” L x 1.42” W x 3.98” H (64 x 36 x 101 mm)
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product
against manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on
products purchased and used in North America and only to the original purchaser of
this product. To receive warranty service, the purchaser must contact La Crosse
Technology, Ltd for problem determination and service procedures. Warranty
service can only be performed by a La Crosse Technology, Ltd authorized service
center. The original dated bill of sale must be presented upon request as proof of
purchase to La Crosse
Technology, Ltd or La Crosse Technology, Ltd’s authorized
service center.
La Crosse Technology, Ltd will repair or replace this product, at our option and at no
charge as stipulated herein, with new or reconditioned parts or products if found to
be defective during the limited warranty period specified above. All replaced parts
and products become the property of La Crosse Technology, Ltd and must be
returned to La Crosse Technology, Ltd. Replacement parts and products assume
the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse
Technology, Ltd will pay all expenses for labor and materials for all repairs covered
by this warranty. If necessary repairs are not covered by this warranty, or if a
product is examined which is not in need or repair, you will be charged for the
repairs or examination. The owner must pay any shipping charges incurred in
getting the La Crosse Technology, Ltd product to a La Crosse Technology, Ltd
authorized service center. La Crosse Technology, Ltd will pay ground return
shipping charges to the owner of the product to a USA address only.
The La Crosse Technology, Ltd warranty covers all defects in material and
workmanship with the following specified exceptions: (1) damage caused by
accident, unreasonable use or neglect (including the lack of reasonable and
necessary maintenance); (2) damage occurring during shipment (claims must be
presented to the carrier); (3) damage to, or deterioration of, any accessory or
decorative surface; (4) damage resulting from failure to follow instructions contained
in the owner’s manual; (5) damage resulting from the performance of repairs or
alterations by someone other than an authorized La Crosse Technology, Ltd
authorized service center; (6) units used for other than home use (7) applications
and uses that this product was not intended or (8) the products inability to receive a
signal due to any source of interference.. This warranty covers only actual defects
within the product itself, and does not cover the cost of installation or removal from
a fixed installation, normal set-up or adjustments, claims based on
misrepresentation by the seller or performance variations resulting from installation-
related circumstances.
LA CROSSE TECHNOLOGY, LTD W ILL NOT ASSUME LIABILITY FOR
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES
ASSOCIATED W ITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.
THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR
PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF
CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have other rights
specific to the State. Some States do not allow the exclusion of consequential or
incidental damages therefore the above exclusion of limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology, Ltd
2817 Losey Blvd. S.
La Crosse, W I 54601
The complete instruction manual is available at:
www.lacrossetechnology.com/616-146
Contact Support: 1-608-782-1610
Product Registration:
www.lacrossetechnology.com/support/register
Protected under U.S. Patents:
5,978,738
6,076,044
6,597,990
FCC Disclaimer:
This Device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) the device must accept any interference received, including interference that
may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO
OPERATE THE EQUIPMENT
All rights reserved. This handbook must not be reproduced in any form, even in
excerpts, or duplicated or processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors. The information in this
handbook is regularly checked and corrections made in the next issue. We accept
no liability for technical mistakes or printing errors, or their consequences.
All trademarks and patents are acknowledged.
Printed in China
