L3 2100-1010-00 Component Maintenance Manual With Illustrated Parts List Download

Page: 296 / 334

COMPONENT MAINTENANCE MANUAL

AVIATION RECORDERS

FA2100CVR

Rev. 15 Page 909

Apr. 14/16

Special Tools and Test Equipment

23–70–04

Use or disclosure of information on this sheet is subject

to the restrictions on the cover page of this document.

RECORDER INTERFACE (RI)

CABLE ASSY.

17TES0057

RECORDER USB FDAU

SIMULATOR (RUFS)

(RI) ADAPTER

17TES0076

FA2100 CVR

RECORDER

INPUT

FA2100 TO CICC/2

COMPUTER INTERFACE

COMMUNICATIONS CABLE

17TES0072

CICC/2

COMPUTER INTERFACE

COMMUNICATIONS CABLE/2

17TES0070

ROSE/RI SOFTWARE

17TES0321 (CDROM)

READ-OUT CENTER/6 or /7

17TES0400 or 17TES0700

Note:

Typical view of the back of

the computer.

Views may vary depending

on the computer

Power

Input

Select

FA2100 SOFTWARE

DISTRIBUTION DISK

840‐EXXX‐XX

Note:

Firmware Distribution
Diskette P/N will match the
FA2100 Software Part
Number located on the
recorder 's Name Plate Label.

ENHANCED

PARALLEL PORT

LPT‐1

(EPP)

FA2100

SOFTWARE UPLOAD

(BOOTLOAD) CABLE ASSEMBLY

17TES0058

(use for software

uploading only)

Note:

RI = Recorder Interface.
ROSE = Read‐Out Support Equipment.
ROC = Read‐Out Center (ROC/5, /6 or /7)

Note:

The ROC rear connections shown in this diagram are for
general reference and may not reflect the exact connector
location or configuration your ROC system computer.

Note:

The 17TES0058 cable assembly should only be attached
during upload process. Not used when downloading data
or getting recorder status.

Figure 903. FA2100CVR Software Upload Connections

Using Computer Interface & Communications Cable (CICC)

The document reference is online, please check the correspondence between the online documentation and the printed version.

Summary of Contents for 2100-1010-00















































































































































































































































































































































Search results

Summary of Contents for 2100-1010-00

Reviews:

Related manuals for 2100-1010-00

Brands by name

Popular brands

L3 2100-1010-00, Component Maintenance Manual With Illustrated Parts List

Search results

Summary of Contents for 2100-1010-00

Reviews:

Related manuals for 2100-1010-00

Brands by name

Popular brands