L-Acoustics KARA II DOWNFILL FOR K1 Addendum Download Page 16 | Manualshive

Page: 16 / 24

background image

Rigging procedures

4.

Disconnect the rear rigging between the two top Kara II enclosures.

Risk of crushing injury.

Keep ngers away from the contact area between the ledge and the cabinet.

Risk of cable damage.

Disconnect any cable from the K1 bottom connector.

5.

Connect KARA-DOWNK1 to the bottom of the K1 array:

a) Rotate the top Kara II upwards and secure the rear KARA-DOWNK1 tabs to the K1 rigging.

16

Kara II downll for K1 addendum (EN) version 1.0

«
...
14
15
16
17
18
...
»

Summary of Contents for KARA II DOWNFILL FOR K1

























Reviews:

No comments

Related manuals for KARA II DOWNFILL FOR K1

Brand: Panasonic Pages: 36

JBL EON ONE Compact

Brand: Harman Pages: 2

Brand: Harman Kardon Pages: 2

Brand: Phase Technology Pages: 6

Brand: Hama Pages: 26

JBL BAR 2.0 PLUS

Brand: Harman Pages: 15

Brand: Ebode Pages: 2

Brand: audiophony Pages: 8

Brand: KEF Pages: 2

Brand: JBL Pages: 4

Brand: B2 Audio Pages: 6

Brand: Okayo Pages: 24

Brand: JBL Pages: 2

Brand: Bose Pages: 52

Brand: Bang & Olufsen Pages: 68

Brand: Mooni Pages: 6

Brand: Insignia Pages: 8

Brand: Jensen Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands