L-Acoustics K3i Owner'S Manual Download Page 17

Page: 17 / 85

Rigging system description

Rigging system description

K3i

The K3i system is the installation version of the K3 system and features a simplied rigging system to optimize visual

impact.
The enclosures are assembled together with rigging plates and rigging accessories suited for installation. Like the K3

system, the enclosures can be deployed in own or stacked arrays. Multiple rigging kits are available depending on the

desired conguration (refer to

System component illustrations

(p.9)).

K3i is compatible with two types of rigging plate kits:

standard rigging plates (K3i-LINK)

end rigging plates (K3i-ENDLINK)

K3i-LINK can be used to add an inter-element angle of 0.25°, 1°, 2°, 3°, 4°, 5°, 7.5° or 10° between two K3i.

1°

4°

7.5°

0.25°

3°

2°

5°

10°

K3i owner's manual (EN) version 1.0

Summary of Contents for K3i






















































































Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands

L-Acoustics K3i, Owner'S Manual

Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands