background image

Connection to LA amplied controllers

Connection to LA amplied controllers

Enclosure drive capacity per amplied controller

Make sure the total number of connected enclosures does not exceed the maximum number of enclosure per controller

(refer to the footnote).

LA4X

LA8

LA12X

per output

 

*

 / 

total

per output

 

*

 / 

total

per output

 

*

 / 

total

K3

1 / 2

2 / 4

3 / 6

Kara II

2 / 4

3 / 6

3 / 6

KS28

1 / 4

KS21

1 / 4

2 / 6 

b

2 / 8

Cabling schemes for K3 / Kara II

Refer to the cabling schemes to connect the enclosures to different types of output connectors.

Two-channel speakON output

SP

SP

1+/1-

2+/2-

Four-channel CA-COM output

DO

SP

D

O

FI

LL

-L

A8

2W  CH(A)

2W  CH(B)

DO

SP

D

O

3W

FI

LL

2WAY

SUB2

SUB1

b

LA8 can drive up to two KS21 or KS21i per output, but no more than six per controller at high level.

*

For passive loudspeakers, the value corresponds to the number of enclosures in parallel on the output. For active

loudspeakers, the value corresponds to the number of sections in parallel on the output.

K3 owner's manual (EN) version 1.0 

 99

Summary of Contents for K Series

























































































































Reviews: