L-3 Technologies CyTerra Range R2D Link Operation &Training Manual Download Page 5

Page: 5 / 102

Approved for Public Release 20 October

2015 by U.S. Army Project Manager I2WD

10/13/2017

Approved for Public Release 20 October

2015 by U.S. Army Project Manager I2WD

CyTerra

INSTRUCTION POINTS

•

The RANGE-R2D system is a portable, handheld, battery-operated system

designed to detect moving and near-stationary targets through walls

constructed of common building materials.

•

The system is comprised of a stepped-frequency

continuous

wave radar

transceiver, digital signal processor, display and power supply electronics

enclosed in a rugged, water-resistant, lightweight plastic housing.

•

The operator controls consist solely of the two momentary push-button

switches located on the sides of the system.

•

The graphics display on the front of the system presents target detection

information and system status.

•

The display is easy to use, alerts are simple to interpret, and detection is

nearly immediate.

Summary of Contents for Range R2D Link







































































































Search results

Summary of Contents for Range R2D Link

Reviews:

Related manuals for Range R2D Link

Brands by name

Popular brands

L-3 Technologies CyTerra Range R2D Link, Operation &Training Manual

Search results

Summary of Contents for Range R2D Link

Reviews:

Related manuals for Range R2D Link

Brands by name

Popular brands