background image

Page

1. Features................................................................................. 1

2. Specifications......................................................................... 2

3. Safety Notes.......................................................................... 4

4. Instrument Layout.................................................................. 6

5. Measuring Method................................................................. 7

5-1. Preparation..................................................................... 7

5-2. Measurements................................................................ 7

5-2-1. DC Current Measurements.......................................... 7

5-2-2. AC Current Measurements......................................... 9

5-2-3. Other Applications...................................................... 10

6. Battery Replacement............................................................ 10

7. Optional Accessories............................................................ 11

7-1. Model 8021 KEW ENERGIZER.................................... 11

7-2. Model 8008 MULTI-TRAN............................................. 12

Contents

Summary of Contents for 8113

















Reviews: