background image

― 1 ―

1. SAFE TESTING

Electricity is dangerous and can cause injury and death. Always treat it
with  the  greatest  of  respect  and  care.  If  you  are  not  quite  sure  how  to
proceed, stop and take advice from a qualified person. This instruction
manual contains warnings and safety rules which must be observed by
the user to ensure safe operation of the instrument and retain it in safe
condition.  Therefore,  read  through  these  operating  instructions  before
using the instrument.

IMPORTANT:

1. This  instrument  must  only  be  used  by  a  competent  and  trained

person  and  operated  in  strict  accordance  with  the  instructions.
KYORITSU  will  not  accept  liability  for  any  damage  or  injury  caused
by misuse or non-compliance with the instructions or with the safety
procedures.

2. It is essential to read and to understand the safety rules contained in

the instructions or with the safety procedures.

3. The symbol     indicated on the instrument means that the user must

refer  to  the  related  sections  in  the  manual  for  safe  operation  of  the
instrument.  Be  sure  to  carefully  read  instructions  following  each
symbol      in this manual.

DANGER

is  reserved  for  conditions  and  actions  that  are  likely  to

cause serious or fatal injury.

WARNING

is  reserved  for  conditions  and  actions  that  can  cause

serious or fatal injury.

CAUTION

is  reserved  for  conditions  and  actions  that  can  cause  a

minor injury or instrument damage.

Summary of Contents for 4116A





















Reviews: