Kyocera TASKalfa 3212i Operation Manual Download | Manualshive

Page: 499 / 616

background image

10-16

Troubleshooting > Troubleshooting

Troubleshooting

Solving Malfunctions

The table below provides general guidelines for problem solving.

If a problem occurs with your machine, look into the checkpoints and perform procedures indicated on the following
pages. If the problem persists, contact your Service Representative.

Machine Operation Trouble

When the following machine operation troubles occur, implement appropriate procedures.

NOTE

When contacting us, the serial number will be necessary.
To check the serial number, refer to the following:

Display for Device Information (page 2-18)

Symptom

Checkpoints

Corrective Actions

Reference

Page

An application does not
start.

Is the Auto Panel Reset time short?

Set the Auto Panel Reset time to 30
seconds or more.

The screen does not
respond when the power
switch is turned on.

Check the power cord.

Connect both ends of the power
cord securely.

―

Is the machine powered on?

Turn on the main power switch.

Pressing the [

Start

] key

does not produce copies.

Is there a message on the screen?

Determine the appropriate response
to the message and respond
accordingly.

Blank sheets are ejected. Are the originals loaded correctly?

When placing originals on the
platen, place them face-down and
align them with the original size
indicator plates.

When placing originals in the
document processor, place them
face-up.

―

Check that the settings of the
application software.

―

Paper often jams.

Is the paper loaded correctly?

Load the paper correctly.

―

Turn the orientation 180 degrees
around in which the paper is
positioned.

Is the paper of the supported type?
Is it in good condition?

Remove the paper, turn it over, and
reload it.

Is the paper curled, folded or
wrinkled?

Replace the paper with new paper.

Are there any loose scraps or
jammed paper in the machine?

Remove any jammed paper.

«
...
497
498
499
500
501
...
»

Summary of Contents for TASKalfa 3212i









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 3212i

Brand: Sagem Pages: 86

ApeoSport C5540I

Brand: Fuji Xerox Pages: 108

ECOSYS M8124cidn

Brand: Kyocera Pages: 44

Brand: Muratec Pages: 6

N2125N - DocuPrint B/W Laser Printer

Brand: Xerox Pages: 335

Brand: InfoPrint Pages: 170

imageCLASS LBP913w

Brand: Canon Pages: 327

Brand: DataCard Pages: 204

10600 - Stylus Pro Color Inkjet Printer

Brand: Epson Pages: 8

1400 - Stylus Photo Color Inkjet Printer

Brand: Epson Pages: 8

10600 - Stylus Pro Color Inkjet Printer

Brand: Epson Pages: 183

Brand: Epson Pages: 279

1400 - Stylus Photo Color Inkjet Printer

Brand: Epson Pages: 4

magicolor 2430 DL

Brand: Konica Minolta Pages: 140

Brand: Ricoh Pages: 12

Brand: Brother Pages: 340

Brand: Brother Pages: 45

DCP 110c - Color Flatbed Multi-Function Center

Brand: Brother Pages: 107

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands