Kyocera TASKalfa 3212i Operation Manual Download | Manualshive

Page: 106 / 616

background image

2-40

Installing and Setting up the Machine > Energy Saver Function

Auto Sleep

Auto Sleep automatically switches the machine into Sleep if left idle for a preset time.

The amount of time before entering Sleep is as follows.

• 1 minute (default setting).

To change the preset sleep time, refer to the following:

Quick Setup Wizard (page 2-42)

Sleep Rules (models for Europe)

You can set whether Sleep Mode operates for each function. When the machine enters Sleep Mode, the ID card cannot
be recognized.

For more information on Sleep Rules settings, refer to the following:

Sleep Rules (models for Europe) (page 8-69)

Sleep Level (Energy Saver) (models except for

Europe)

This mode reduces power consumption even more than normal Sleep Mode, and allows Sleep Mode to be set
separately for each function. Printing from a computer connected with a USB cable is not available while the machine is
asleep. The time required for the machine to wake up from power save mode and resume normal operation will be
longer than for normal Sleep Mode.

For more information on Sleep Level (Energy Saver) Mode settings, refer to the following:

Quick Setup Wizard (page 2-42)

Energy Saver Recovery Level

This machine can reduce power consumption when recovering from Energy Saver Mode.

For EnergySaver RecoveryLevel, "Full Recovery", "Normal Recovery" or "Power Saving Recovery" can be selected.

The factory default is "Normal Recovery".

For more information on Energy Saver Mode settings, refer to the following:

Quick Setup Wizard (page 2-42)

EnergySaver RecoveryLevel (page 8-70)

Weekly Timer Settings

Set the machine to automatically turn OFF and wake up at times specified for each day.

For more information on Weekly Timer Settings, refer to the following:

Quick Setup Wizard (page 2-42)

NOTE

If the Low Power Timer is equal to the Sleep Timer, a Sleep Mode is preceded.

NOTE

If the optional Network Interface Kit is installed, Energy Saver cannot be specified.

«
...
104
105
106
107
108
...
»

Summary of Contents for TASKalfa 3212i









































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 3212i

Brand: LabelTac Pages: 2

Panafax UF-7000

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 120

Brand: Panasonic Pages: 100

KX-MB781 - B/W Laser - All-in-One

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 130

Brand: Oki Pages: 210

Brand: Panasonic Pages: 77

Brand: Panasonic Pages: 402

Brand: Panasonic Pages: 54

Workio DP-8016P

Brand: Panasonic Pages: 88

Brand: Panasonic Pages: 60

Brand: Canon Pages: 18

MultiPASS MPC190

Brand: Canon Pages: 8

Komax ims 295 BC

Brand: WIEDENBACH Pages: 52

Brand: DataCard Pages: 130

Brand: Oki Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands