background image

check the tightness of terminal screws and the general 
condition of the wiring.  
Also, check to be sure that mounting hardware is tight. 
Loose bolts could result in a damaged module or array. 
 
12. WARNINGS 
Solar modules are live electrical power sources when 
ex- posed to light. Arrays of many modules can cause 
lethal shock and burn hazards. Solar modules should be 
covered with an opaque material during installation to 
avoid shocks or burns. Do not touch live terminals with 
bare hands. Use insulated tools for electrical 
connections. 
 
PERMIT
 
- Before installing your solar system, contact local 
authorities to determine the necessary permit, 
installation and inspection requirements. 
 
INSTALLATION AND OPERATION 

• 

Systems should be installed by qualified 
personnel only. The system involves electricity, 
and can be dangerous if the personnel are not 
familiar with the appropriate safety procedures. 

• 

Do not step on the module. 

• 

Although KYOCERA modules are quite rugged, 
the glass can be broken (and the module will no 
longer work properly) if it is dropped or hit by 
tools or other objects.  

• 

Sunlight shall not be concentrated on the 
module. 

• 

The module frames is made of anodized 
aluminum, and therefore corrosion can occur if 
the module is subject to a salt water 
environment with contact to a rack of an- other 
type of metal.(Electrolytic Corrosion) 

 
GROUNDING 

• 

All module frames and mounting racks must be 
properly grounded in accordance with the 
appropriate electrical codes. 

 
INSPECTION
 

• 

Follow the requirements of applicable National 
and local electrical safety Codes. 

 
BATTERY
  

• 

When solar modules are used to charge 
batteries, the battery must be installed in a 
manner which will protect the performance of the 
system and the safety of its users. The battery 
should be away from the main flow of people 
and animal traffic. Select a battery site that is 
protected from sunlight, rain, snow, debris, and 
is well ventilated. Most batteries generate 
hydrogen gas when charging, which is 
explosive. Do not light matches or create sparks 
near the battery bank. When a battery is 
installed outdoors, it should be placed in an 

insulated and ventilated battery case specifically 
designed for the purpose. 

 
 

 

 
 

NOTES The electrical characteristics are within ±10 
percent of indicated values of lsc, Voc, and Pmax under 
standard test conditions (irradiance of 1KW/m², AM 1.5 
spectrum, and cell temperature of 25

Û&

 

Under conditions, a photovoltaic module is likely to pro- 
duce more current and / or voltage than reported at 
standard test conditions. Accordingly, the values of lsc 
and Voc marked on this module should be multiplied by 
a factor of 1.25 when determining component voltage 
ratings, conductor ampacities, fuse sizes, and sizes of 
regulators which are connected to the PV output. Refer 
to Section 690-8 of the National Electrical Code for an 
additional multiplying factor of 125 (80 per cent 
derating), which may also be applicable.  
 

 
 

 

Manufactured by:  Kyocera Corporation 
 

 

      Made in Japan 

 

Kyocera Solar, Inc. 
7812 East Acoma Dr. 
Scottsdale, AZ 85260 
Phone:     800-223-9580 
                 480-948-8003 
Fax:          480-483-2986 
Email:       

[email protected]

 

Web site:  www.kyocerasolar.com 

Summary of Contents for KC-TYPE

Page 1: ... avoid trees buildings or obstructions which could cast shadows on the solar modules especially during the winter months when the arc of the sun is lowest over the horizon 5 MODULE TILT ANGLE Solar modules produce the most power when they are pointed directly at the sun For installations where the solar modules are mounted to a permanent structure the solar modules should be tilted for optimum win...

Page 2: ...cover by loosening the screws in the cover Figure 4 and 5 B The wire typically used to interconnect the solar modules should be single or two conductor from 10 AWG 5 26 mm up to 14 AWG 2 08 mm gauge stranded copper wire in a SUNLIGHT RESISTANT jacket UF cable This cable is suitable for applications where wiring is exposed to the direct rays of the sun The maximum and minimum diameter of the cable ...

Page 3: ...by reverse current flow KYOCERA modules do not contain a blocking diode when shipped from the factory however most battery charging regulators do have this feature 10 BYPASS DIODES Partial shading of an individual module in a 12 volt or higher series string i e two or more modules can cause a reverse voltage across the shaded module Current is then forced through the shaded area by the other modul...

Page 4: ...al codes INSPECTION Follow the requirements of applicable National and local electrical safety Codes BATTERY When solar modules are used to charge batteries the battery must be installed in a manner which will protect the performance of the system and the safety of its users The battery should be away from the main flow of people and animal traffic Select a battery site that is protected from sunl...

Reviews: