manualshive.com logo in svg

Kyocera Copystar CS-1635, Service Manual

The Kyocera Copystar CS-1635 is a reliable office copier known for its exceptional performance and user-friendly interface. Enhance your productivity with this versatile device by easily accessing its Service Manual. You can download the manual for free from our website, empowering you to troubleshoot and optimize its functionalities.

Share
Download
background image

2HA/2HB

1-3-21

U070

Adjusting the DP magnification
Description

Adjusts the DP original scanning speed.

Purpose

Make the adjustment if the magnification is incorrect in the auxiliary scanning direction when the optional DP 
is used.

Caution

Before making this adjustment, ensure that the following adjustments have been made in maintenance mode

Method

Press the start key.

Adjustment

1. Select the item using the exposure adjustment keys.

2. Press the interrupt key.
3. Place an original on the DP and press the start key to make a test copy.
4. Change the setting value using the zoom +/- keys.

For copy example 1, increase the value.
For copy example 2, decrease the value.

Figure 1-3-10

5. Press the start key. The value is set.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Maintenance

item No.

Description

U065

(P.1-3-18)

U053

(P.1-3-16)

U070

Exposure
indicator

Description

Setting
range

Initial
setting

Exp. 1

Original conveying motor speed (First side)

-25 to 25

0

Exp. 2

Original conveying motor speed (Second side)

-25 to 25

0

Original

Copy

example 1 

Copy

example 2

Summary of Contents for Copystar CS-1635





















































































































































































































































Reviews:

No comments

Related manuals for Copystar CS-1635

Canon MX490 Series Setup Manual preview
MX490 Series
Brand: Canon Pages: 11
Canon MX490 Series Quick Help Manual preview
MX490 Series
Brand: Canon Pages: 2
Canon Photura 135 Review preview
Photura 135
Brand: Canon Pages: 12
Canon PIXMA Pro9000 Mark II Series Release Note preview
PIXMA Pro9000 Mark II Series
Brand: Canon Pages: 4
WaxJet 6100 Service Reference Manual preview
6100
Brand: WaxJet Pages: 131
Oki ES7131 User Manual preview
ES7131
Brand: Oki Pages: 137
Xerox DocuPrint C3055 DX Settings Manual preview
DocuPrint C3055 DX
Brand: Xerox Pages: 20
Colorjet Verve Hybrid Installation And Troubleshoot Manual preview
Verve Hybrid
Brand: Colorjet Pages: 52
Ricoh AficioSP C410DN Hardware Manual preview
AficioSP C410DN
Brand: Ricoh Pages: 204
Xerox LS 3270 User Manual preview
LS 3270
Brand: Xerox Pages: 55
Citizen CT-S4000DCL User Manual preview
CT-S4000DCL
Brand: Citizen Pages: 4
Radio Shack Line Printer VIII Hardware Manual preview
Line Printer VIII
Brand: Radio Shack Pages: 54
Star Micronics Multi-Font NX-2415 User Manual preview
Multi-Font NX-2415
Brand: Star Micronics Pages: 134
Screen Print & Inkjet Fast T-Jet Blazer Pro User Manual preview
Fast T-Jet Blazer Pro
Brand: Screen Print & Inkjet Pages: 138
Ricoh P 501 Setup Manual preview
P 501
Brand: Ricoh Pages: 24
Nehoc TCA3-SP User Manual – Operating Manual preview
TCA3-SP
Brand: Nehoc Pages: 9
Xerox DocuPrint 205 Settings Manual preview
DocuPrint 205
Brand: Xerox Pages: 34
Oki ES8140 User Manual preview
ES8140
Brand: Oki Pages: 83

Brands by name

Popular brands

Load more brands