Kyocera AJP-1100, Owner'S Operating Manual

Page: 8 / 12

7
After Use
1. Turn the main switch to the OFF position.
2. Turn the water faucet off.
3. Depress the spray gun trigger until all water has
stopped flowing from the nozzle.
4. Pull the hose joint coupler forward to release the water
supply hose from the water connector.
5. Depress the spray gun safety lock button to lock the
trigger.
6. Press the release button (26) to remove the spray gun
hose (10) from the main unit. (Fig. 16)
7. Remove remaining water from the main unit
Turn the main switch to the ON position for 1-2 seconds
to discharge excess water from the spray gun hose
connection port.
WARNING! Exercise caution as the released of excess
water is highly pressurized
WARNING! Leaving the main switch on for longer than
2 seconds may damage the unit. Be sure to turn the
main switch off immediately.
8. Unplug the power cord.
9. Remove the water supply hose from the faucet.
10. Press the release button (27) to remove the spray gun
hose (10) from the spray gun (9). (Fig. 17)
WARNING!
Remove all excess water from the main unit, spray gun
hose, spray gun and nozzles especially in cold weather.
Storing the unit in cold temperatures without removing all
excess water may damage the unit and cause malfunction.
Self-priming kit (optional accessory)
Use with alternative water sources (Fig.18)
By attaching self-priming kit, which is an optional
accessory, this machine can draw in water from
alternative water sources, such as water butts and
water containers.
* Need to prime the hose beforehand to remove the air
bubble inside the hose.
* The discharge pressure will be lower compared with
when supplying water from a faucet.
note: Make sure to operate this machine on level ground.
Things to prepare
• Self-priming kit (Fig.19)
• Water for priming the hose (approximately 1L)
• Water container
• Water for cleaning
How to use
WARNING! Make sure to clean the Self-priming
filter, the strainer on Self-priming hose, and filter
on the machine, before connecting. It will cause low
discharge pressure or malfunction of the machine
when using with the dust adhered.
1. Remove spray gun hose from the machine.
• Press the release button (26) to remove the spray gun
hose (10) from the main unit. (Fig. 16)
2. Attach Self-priming filter.(Fig.20)
* Remove water supply hose(16) and water connector
(12) if they are set.
• Attach Self-priming filter (29) into water inlet by turning
clockwise.
note:
• Tighten Self-priming filter straight onto the water inlet
by turning it in a clockwise direction(If the filter is not
tighten correctly onto the inlet, leaking may occur).
• Make sure that the filters on Self-priming filter and
machine are correctly set. Operating without the filters
cause the malfunction of the machine.
• Rubber seal is set inside of filter caps of the connector
and the Self-priming filter. Please be careful not to
lose them when removing.(Fig.21)
3. Attach Self-priming hose onto Self-priming filter.
(Fig.22)
• Insert Self-priming hose (30) straight into Self-priming
filter(29) and securely tighten by turning the ring (36).
note: Pulling the Self-priming hose forcefully left or
right may cause water leakage from the connection
part.
4. Remove the strainer from Self-priming hose by
turning it. (Fig.23)
note :
Be careful with the connecting part of strainer as
some wire may be come out unexpectedly.
5. Pour water into Self-priming hose from the water
supply side. (Fig.24)
• Lift up the self-priming hose higher than the machine,
and then pour water (approximately 1L) slowly until the
hose is totally filled.
• Set strainer onto Self-priming hose in the reverse
order of removing it.
note : Make sure to adjust the screw thread of the
strainer and hose before tightening to avoid the
breakage of the screw thread.
6. Put the strainer into water container filled with
water. (Fig.25)
• Make sure that no air enter inside of Self-priming
hose.
7. Check whether the water is supplied.(Fig.26)
• Turn on the machine and check whether the water is
supplied or not. If there is no problem, turn it off.
Ready to use.
Connect the spray gun hose and start the operation.
When the machine does not suck up water properly or
water leakage is occurred, the following cause may be
concerned.
• Self-priming filter is not fully tightened.
• Self-priming filter is not properly attached onto water
inlet.
• The filter inside of Self-priming filter is not properly set,
and there is space between filter and rubber seal.
If the above-problem occurs, remove Self-priming filter and
then set it again in the following procedure:
1. Confirm that the filter inside of
Self-priming filter is set properly
by loosing the filter cap (Fig. A).
2. Hold the filter case vertically and
tighten the filter cap securely.
3. Tighten Self-priming filter onto
the water inlet of the machine
securely.
The filter is
properly set
The filter is
not properly set
A